BEGA 85130 Performance Floodlight Instruction Manual

Table of Contents

Specifications:
- Product Name: Performance Floodlight
- Model Number: 85 130
- Power Consumption: 8.4 W – 9.6 W
- Colour Temperature: 3000 K / 4000 K
- Colour Rendering Index (CRI): > 90
- Luminous Flux: 1265 lm – 1330 lm
- Luminous Efficiency: 96.5 lm/W – 101.5 lm/W

Application:
- The Performance Floodlight is designed for a variety of interior and exterior lighting applications.
Safety Information:
- Installation and operation must comply with national safety regulations.
- Only a qualified electrician should perform the installation and commissioning.
- The manufacturer is not liable for damage due to improper use or installation. Any modifications should be done by authorized personnel.
Overvoltage Protection:
- The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547.
- For additional protection against transients, separate overvoltage protection components are recommended, available on the manufacturer’s website.
Installation:
- LED components are sensitive; avoid direct contact with the light output opening during installation or relamping.
- To install, place the floodlight unit on the mounting plate as shown in the diagram, align it, and securely screw it together.
- To adjust the beam direction, loosen the joint screw with a 3 mm hexagon socket head wrench, set the desired direction, and tighten the screw to a torque of 2.5 Nm.

Q: Can I install the Performance Floodlight myself?
- A: Installation and commissioning should only be done by a qualified electrician to ensure the safety and proper functioning of the product.
Q: What should I do if I need to make modifications to the luminaire?
- A: Any modifications to the luminaire should be carried out by authorized personnel to maintain product integrity and safety standards.

$BEGA-85130-Performance-Floodlight-FIG-1 $1$$

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Clear safety glass
Silicone gasket
The reflector surface is made of pure aluminium
BEGA Hybrid Optics®
The rotation range of floodlight is 350°
Swivel range -30°/+80°
Mounting box with 2 fixing holes ø 4.8mm · 35mm spacing 1 cable entry for mains supply cable up to ø 10,5mm
Connecting terminals 2.5@
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK07
Protection against mechanical impacts < 2 joule
Conformity mark
Wind catching area: 0.01 m²
Weight: 0.9 kg
This product contains light sources of energy efficiency class(es) D

Lamp

85 130K3

85 130K4

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the hexagon socket head screw (wrench size 3mm) up to the stop and disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note the position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make an earth conductor connection.
Push silicone sleeves over the lines and make the electrical connection.
Connect the floodlight unit’s green and yellow protective earth conductor to the terminal marked in the mounting plate. Make sure that the gasket is positioned correctly. $BEGA-85130-Performance-Floodlight-FIG-1 $3$$
Place the floodlight unit onto the mounting plate as displayed in the sketch, and align and screw together firmly.

Adjustment of beam direction:

Undo the joint screw (hexagon socket head wrench size 3 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 2.5Nm.

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Maintenance

The connecting cable between the mounting box and floodlight has to be inspected for obvious damages and has to be replaced by a qualified electrician only.

Please note:

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
Disconnect the system from the power supply.

Open the floodlight:

Remove the trim ring along with the safety glass and reflector by twisting it anti-clockwise.
Replace the LED module.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Place the trim ring with glass and reflector on the floodlight housing so that the notches in the trim ring and luminaire housing sit on top of each other.
Twist on the trim ring clockwise as far as the stop.