V-TAC VT-66 LED Solar Light Installation Guide
- June 6, 2024
- V TAC
Table of Contents
WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED SOLAR LIGHT
TECHNICAL SPECIFICATIONS
| MODEL | VT-66 |
|---|---|
| WATTS | 2W |
| LUMENS | 280LM |
| BEAM ANGLE | 120 |
| CRI | >80 |
| IP RATING | IP65 |
INTRODUCTION & WARRANTY
Thank you for selecting and buying the V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at your best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product.
WARNING!
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Installation should be done by a certified electrician.
This marking indicates that this product should not be disposed of with other household wastes
MULTI-LANGUAGE MANUAL QR CODE
https://vtacexports.com/pub/media/ftp-upload/manuals/VT-66.html
Please scan the QR code to access the manual in multiple languages.
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
SOLAR LIGHT
INSTALLATION DIAGRAM
|
|
---|---|---
I. Ground installation instructions:
- After confirming the installation position, fix the grounding support with screws. As shown in Figure 1.
- Install the lamp onto the bracket and tighten the screw with a six-legged wrench. As shown in Figures 2 & 3.
II. Surface-mounted installation instructions:
- Choose the appropriate installation position and fix the installation bracket with screws. Picture 1.
- Install the lamp on the mounting bracket and tighten the screw by hand with a six-legged wrench.
Switch Function:
– Press and hold the button for 2-3 seconds to switch ON the solar light. Once
switched ON it will indicate a blue light.
– When switching on the solar light by default it will be in Mode 1.
– To enter Mode 2, press the button again.
– Pressing the button for the third time the solar light will switch OFF and
the blue light will disappear.
Operating Modes:
Mode 1: Sensor Mode.
– At dusk, it automatically turns to 10% brightness.
– Turns on to 100% brightness when motion is detected in the range of <5
meters.
– In 30 seconds if no motion is detected the light switches to 10% brightness.
– Turns off at the dawn.
Mode 2: Constant Brightness Mode.
– The sensor will be disabled.
– Automatically turns on at the dusk with 100% brightness and works constantly
till the battery capacity goes to Zero. (Up to 4 hours).
STRUCTURE AND SIZE
NOTES
- This production is a solar energy product. When installing, the solar panels of the product must be illuminated in the direction of the sun. If not placed in the direction of the sun the lamp will not function properly. Resulting in the lamp not switching ON or the light is functioning for a short period of time only. The solar panels should be placed in the direction of the sunlight. The performance of the light is the best if the illumination time of the sunlight is longer than 6 hours resulting in the light being turned on for its maximum time.
- This product is mainly installed on the wall and is not allowed to be used in damp or immersed places. Otherwise, it will have a breakdown and affect its service life.
- The product can achieve the expected brightness and light-up time when the battery is full of electricity. Such as overcast and rainy days, which will cause insufficient charging and shorten the light-uptime. If the lighting time is not long on sunny days, please check whether the solar panels are exposed to the sun for a long time. Or whether the solar panel is dirty and dusty, ensure to keep the solar panels clean.
- LED Solar light is designed with a replaceable battery. It should be replaced after 3 years of use. After removing the wire connection from the original lithium battery, the battery will be removed and replaced with the new battery of the same specifications.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>