AViANCE HD48546 3 Light Antique Brass Vanity Light Instruction Manual
- June 1, 2024
- AVIANCE
Table of Contents
AViANCE HD48546 3 Light Antique Brass Vanity Light
Product Information
Specifications:
- Model: HD48546
- Power Source: Electrical
- Material: Metal, Glass
- Wattage: Refer to the fixture’s specifications
- Bulbs: Not included
Product Usage Instructions
Assembling the Fixture:
- Turn off the power at the circuit breaker box and remove old fixture from the Junction Box.
- Unpack the new fixture, lay out all parts, and ensure no small parts are lost.
- Drill two holes in the wall, attach the mounting plate to the wall using plastic anchors, wood screws, and box screws.
- Guide fixture wires through the back plate’s center hole.
- Follow wiring instructions carefully as shown in Fig.2.
- Attach the lamp body to the mounting plate, secure it with the ball nut.
- Secure the glass shade to the lamp holder using the check ring.
- Install light bulbs according to the fixture’s specifications. Do not exceed maximum wattage rating.
Connecting the Wires:
- Connect Black wire from fixture to black house (hot) wire, and white wire to white (neutral) house wire. Secure wire nuts and wrap connections with electrical tape if needed.
- If your outlet box has ground wires, connect fixture’s ground wire to it. Otherwise, attach bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck wire connections neatly into the wall junction box.
Your installation is complete. Restore power to the junction box and test the fixture.
Contact Customer Service:
If you need assistance with parts or assembly, please email customer service
at info@aviancelighting.net.
Thank you for purchasing an AVIANCE product.
FAQ:
-
Q: What should I do if I lose small parts during assembly?
A: Contact customer service at info@aviancelighting.net for assistance in obtaining replacement parts. -
Q: Can I use bulbs with wattage higher than the maximum rating specified?
A: No, it is important not to exceed the maximum wattage rating to prevent damage to the fixture and ensure safety.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ASSEMBLING THE FIXTURE
- Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
- Drilling two holes in the wall, distance and the same distance from the keyhole of the mounting plate, then loaded plastic anchors(A). Attach the mounting plate(B) to the wall, aligning the plastic anchors(A) and junction box, lock it securely with the two wood screws(D) and the two box screws(E). The side of the back plate marked “GND” must face out. The junction box is not included.
- Guide fixture wires through hole in centre of back plate.
- Follow wiring instructions carefully (see fig.2).
- Place the lamp body(H) onto the mounting plate so that the studs(C) protrude through the cover plate holes, then tighten it with the ball nut(I).
- Raise the glass shade(G) to the lamp holder and using the check ring(F) by turning it clockwise until tight.
- Install the light bulbs(Not included) by the fixture’s specifications.
NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
CONNECTING THE WIRES
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has ground wires (green or bare copper) connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product. Need assistance with parts or
assembly? Please email customer service at:
info@aviancelighting.net
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>