AViANCE Lighting HD29132 19.75 Inch 3-Light Brushed Nickel ADA Vanity Installation Guide
- June 1, 2024
- AViANCE lighting
Table of Contents
AViANCE Lighting HD29132 19.75 Inch 3-Light Brushed Nickel ADA Vanity
Product Specifications
- Model: HD29132
- Fixture Type: Ceiling Fixture
- Bulb Compatibility: 60W Candela bulb (not included)
- Power Source: Electrical Wiring
- Grounding: Green or bare copper wire
Product Usage Instructions
Assembling & Installation
The installation instructions provided are general and apply to the product
despite any minor variations in the actual product received.
- Shut off power at the circuit breaker box.
- Remove the old fixture and all hardware from the Junction Box.
- Unpack the new fixture carefully and lay out all parts in a clear area to avoid losing any small pieces.
- Attach the mounting plate to the junction box using two junction screws.
Connecting the Wires
- Connect the electrical wires:
- Black wire from the fixture to the black house (hot) wire.
- White wire from the fixture to the white (neutral) house wire.
- Secure all wire connections with wire nuts and consider wrapping them with electrical tape for safety.
- If present, connect the fixture’s ground wire to the green or bare copper ground wire; otherwise, attach it to the green ground screw on the mounting plate.
- Neatly tuck the wire connections into the wall junction box.
Your installation is now complete. Restore power to the junction box and test the fixture.
Frequently Asked Questions (FAQ)
-
Q: What type of bulb should I use with this fixture?
A: The fixture is compatible with a 60W Candela bulb (not included). -
Q: How do I get assistance with parts or assembly?
A: For any assistance with parts or assembly, please email customer service at info@aviancelighting.net
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.HD29132
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
MOUNTING THE FIXTURE
-
Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
-
Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
-
Attach the mounting plate to the junction box using two junction box screws as shown. The side of the single bar marked “GND” must face out. The junction box is not included.
-
Guide fixture wires through the hole in the centre of the mounting plate.
-
Follow wiring instructions carefully (see fig.2).
-
Install the light bulbs(Not included) according to the fixture’s specifications. NOTE: DO NOT EXCEED THE MAXIMUM\
WATTAGE RATING! -
Insert the glass shade (A) into the ring of the fixture body (B). Attach the small square shim plate to the other end of the fixture body(B), then lock it securely with the screw.
-
Place the fixture body (B) over the mounting plate, aligning the backplane holes with the mounting screws, then lock it securely with the ball nuts(C).
-
This lamp can be vertically installed, however, the square tube of the lamp body has a hook at one end that must be down. Follow wiring instructions carefully.
CONNECTING THE WIRES
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has ground wires (green or bare copper) connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test
the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:
info@aviancelighting.net
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC.