RadioLink RC6GS V2 Radio Control User Guide
- June 13, 2024
- RADioLink
Table of Contents
- Important Information
- SUMMARY OF TEST RESULTS
- Photo of the Submitted Sample
- Additional Photo
- Over views
- Test Result(s)
- APPENDIX
- Pb/Cd/Hg/Cr6+ Testing Flow Chart
- PBBs/PBDEs Testing Flow Chart
- Phthalates Testing Flow Chart
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RadioLink RC6GS V2 Radio Control
Important Information
Applicant : Radiolink Electronic Limited
Address : 3/F,Building 2, Fuguo industrial park, Kaifeng Road, Meilin,
Shenzhen, Guangdong China
The following merchandise was (were) submitted and identified by client as:
Sample Name : Radio Control
Model No. : RC6GS V2
Additional No.: RC4GS V2 with R7FG Receiver
Test Period : From Oct.14, 2021 to Oct.19, 2021
SUMMARY OF TEST RESULTS
| TEST REQUESTED | CONCLUSION |
|---|
Heavy Metals , Flame Retardants and Phthalates Content – European Council Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) with its Amendments Commission Delegated
Directive (EU) 2015/863
| PASS
Test Result (s): Please refer to next page(s).
Unless otherwise stated the results shown in this report refer only to the sample(s) tested. This test report cannot be reproduced, except in full. Without prior written permission of the company,
Guangdong Safety Testing Co., Ltd.
No.1, the 1st North Industry Road, Songshan Lake Sci.&Tech. Park, Dongguan,
Guangdong, China
Tel:86-769-23105888 Fax: 86-769-22899858 http://www.sft-cert.com/
Photo of the Submitted Sample
Additional Photo
Over views
| Test Item(s) | Component Description(s) | Style |
|---|---|---|
| 1 | Black plastic | – |
| 2 | White soft plastic wire jacket | – |
| 3 | Black plastic with gray coating | – |
| 4 | Transparent plastic with black/red/white printing with adhesive | – |
| 5 | Black foam | – |
| 6 | Black plastic with gray coating | – |
| 7 | Silver solder tin | – |
| 8 | Black soft plastic wire jacket with white printing | – |
| 9 | Red soft plastic wire jacket with white printing | – |
| 10 | Red soft plastic wire jacket with black printing | – |
| 11 | Black soft plastic wire jacket with white printing | – |
| 12 | Silver metal with black coating | – |
| 13 | Black plastic with gray coating | – |
| 14 | Red soft plastic wire jacket with black printing | – |
| 15 | Black soft plastic wire jacket with white printing | – |
| 16 | Blue soft plastic wire jacket with white printing | – |
| 17 | Transparent plastic | – |
| 18 | Black foam with adhesive | – |
| 19 | Gray/red soft plastic wire jacket | – |
| 20 | Beige plastic | – |
| 21 | Red soft plastic wire jacket | – |
| 22 | Black soft plastic wire jacket | – |
| 23 | Transparent glass | – |
| 24 | FPC | – |
| 25 | Red soft plastic wire jacket | – |
| 26 | Yellow soft plastic wire jacket | – |
| 27 | Black soft plastic wire jacket | – |
| 28 | Red soft plastic wire jacket | – |
| 29 | White soft plastic wire jacket | – |
| 30 | Black soft plastic wire jacket | – |
| 31 | Beige plastic | – |
| 32 | PCB | – |
| 33 | Silver solder tin | – |
Test Result(s)
Heavy Metals , Flame Retardants Content – European Council Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) with its Amendments Commission Delegated Directive (EU) 2015/863
| Test Method: | See Appendix. |
|---|
See Analytes and their corresponding Maximum Allowable Limit in Appendix
Parameter| Lead
(Pb)
| Cadmium
(Cd)
| Mercury
(Hg)
| Chromium
VI (Cr VI)
| PBBs| PBDEs| Conclusion
---|---|---|---|---|---|---|---
Unit| mg/kg| mg/kg| mg/kg| mg/kg| mg/kg| mg/kg| –
Test Item(s)| –| –| –| –| –| –| –
001| ND| ND| ND| ND| ND| ND| PASS
002| ND| ND| ND| ND| ND| ND| PASS
003| ND| ND| ND| ND| ND| ND| PASS
004| ND| ND| ND| ND| ND| ND| PASS
005| ND| ND| ND| ND| ND| ND| PASS
006| ND| ND| ND| ND| ND| ND| PASS
007| ND| ND| ND| ND| NA| NA| PASS
008| ND| ND| ND| ND| ND| ND| PASS
009| ND| ND| ND| ND| ND| ND| PASS
010| ND| ND| ND| ND| ND| ND| PASS
011| ND| ND| ND| ND| ND| ND| PASS
012| ND| ND| ND| ND| NA| NA| PASS
013| ND| ND| ND| ND| ND| ND| PASS
014| ND| ND| ND| ND| ND| ND| PASS
015| ND| ND| ND| ND| ND| ND| PASS
016| ND| ND| ND| ND| ND| ND| PASS
017| ND| ND| ND| ND| ND| ND| PASS
018| ND| ND| ND| ND| ND| ND| PASS
019| ND| ND| ND| ND| ND| ND| PASS
020| ND| ND| ND| ND| ND| ND| PASS
021| ND| ND| ND| ND| ND| ND| PASS
022| ND| ND| ND| ND| ND| ND| PASS
023| ND| ND| ND| ND| ND| ND| PASS
024| ND| ND| ND| ND| ND| ND| PASS
025| ND| ND| ND| ND| ND| ND| PASS
026| ND| ND| ND| ND| ND| ND| PASS
027| ND| ND| ND| ND| ND| ND| PASS
028| ND| ND| ND| ND| ND| ND| PASS
029| ND| ND| ND| ND| ND| ND| PASS
030| ND| ND| ND| ND| ND| ND| PASS
031| ND| ND| ND| ND| ND| ND| PASS
032| ND| ND| ND| ND| ND| ND| PASS
---|---|---|---|---|---|---|---
033| ND| ND| ND| ND| NA| NA| PASS
Note / Key:
ND = Not detected “>” = Greater than
NA= Not applicable mg/kg = milligram(s) per kilogram = ppm = part(s) per
million
% = percent 10000 mg/kg = 1 %
Detection Limit: See Appendix
Phthalates Content – European Council Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) with its Amendments Commission Delegated Directive (EU) 2015/863
| Analyte | Requirement (mg/kg) | Result (mg/kg) |
|---|
Test Item
1+3| 2+10+11| 6+32
Dibutyl phthalate (DBP)| 1000| ND| ND| ND
Di-(2-ethyl hexyl) phthalate (DEHP)| 1000| ND| ND| ND
Benzyl butyl phthalate (BBP)| 1000| ND| ND| ND
Di-(iso-butyl) phthalate (DIBP)| 1000| ND| ND| ND
Conclusion| PASS| PASS| PASS
Analyte| Requirement (mg/kg)| Result (mg/kg)
---|---|---
Test Item
8+9+19| 14+15+16| 25+26+27
Dibutyl phthalate (DBP)| 1000| ND| ND| ND
Di-(2-ethyl hexyl) phthalate (DEHP)| 1000| 70| 80| 70
Benzyl butyl phthalate (BBP)| 1000| ND| ND| ND
Di-(iso-butyl) phthalate (DIBP)| 1000| ND| ND| ND
Conclusion| PASS| PASS| PASS
Analyte| Requirement (mg/kg)| Result (mg/kg)
---|---|---
Test Item
28+29+30| –| –
Dibutyl phthalate (DBP)| 1000| ND| –| –
Di-(2-ethyl hexyl) phthalate (DEHP)| 1000| ND| –| –
Benzyl butyl phthalate (BBP)| 1000| ND| –| –
Di-(iso-butyl) phthalate (DIBP)| 1000| ND| –| –
Conclusion| PASS| –| –
Note / Key:
ND = Not detected “>” = Greater than
NA= Not applicable mg/kg = milligram(s) per kilogram = ppm = part(s) per
million
% = percent 10000 mg/kg = 1 %
Report Limit: See Appendix.
Remark:
-
The testing approach is listed in table of Appendix.
-
- denotes as reported result(s) was (were) performed by wet chemistry method. Others were screened by XRF.
For XRF screening, the result(s) of Cr VI was (were) reported as total chromium and the result(s) of PBBs and PBDEs was (were) reported as total bromine. Also, the XRF result(s) may be different to the actual content based on various factors including, but not limit to, sample size, thickness, area, non-uniformity composition, surface flatness.。
- denotes as reported result(s) was (were) performed by wet chemistry method. Others were screened by XRF.
-
Only selected example(s) is (are) indicated on the photograph(s) in Comment.
-
According to European Council Directive 2011/65/EU, Article 5 “Adaptation of the Annexes to scientific and technical progress”, exemption(s) should be granted to the materials and components of Test Item(s) in the lists in Annexes III and IV of this directive.
-
Result(s) of Cr VI for metallic material(s) was (were) expressed in term of positive and negative. Negative means the absence of Cr VI on the tested areas and the result(s) was (were) regarded as in compliance with European Council Directive 2011/65/EU, Article 4(1). While, positive means the presence of Cr VI on tested areas and the result(s) was (were) regarded as in conflict with European Council Directive 2011/65/EU, Article 4(1).
-
a. The sample is positive for Cr6+ if the Cr6+ concentration is greater than 0.13µg/cm2 , The sample coating is considered to contain Cr6+.
b. The sample is negative for Cr6+ if the Cr6+ is N.D. (concentration less than 0.10µg/cm2 ), The coating is considered a non-Cr6+ based coating.
c. The result between 0.10µg/cm2 and 0.13µg/cm2 is considered to be inconclusive-unavoidable coating variations may influence the determination information on storage conditions and production date of the tested sample is unavailable and thus Cr6+ results represent status of the sample at the time of testing.
APPENDIX
List of Analytes and their Corresponding Test Methods, Detection Limit and Maximum Allowable Limit [for
European Council Directive 2011/65/EU &(EU) 2015/863 ] :
No.| Name of Analytes| Report Limit (mg/kg)| Maximum
Allowable Limit (mg/kg)
X-ray fluorescence (XRF) [a]| Wet Chemistry
Plastic| Metallic
/ glass / ceramic
| Others
1| Lead (Pb)| 100| 200| 200| 10[b]| 1000
2| Cadmium (Cd)| 50| 50| 50| 10[b]| 100
3| Mercury (Hg)| 100| 200| 200| 10[c]| 1000
4| Chromium (Cr)| 100| 200| 200| NA| NA
5| Chromium VI (Cr VI)| NA| NA| NA| 10[d] /
See [e]
| 1000 / Negative
6| Bromine (Br)| 200| NA| 200| NA| NA
7| Polybromobiphenyls (PBBs)
– Bromobiphenyl (MonoBB)
– Dibromobiphenyl (DiBB)
– Tribromobiphenyl (TriBB)
– Tetrabromobiphenyl (TetraBB)
– Pentabromobiphenyl (PentaBB)
– Hexabromobiphenyl (HexaBB)
– Hepta Bromobiphenyl (HeptaBB)
– Octabromodiphenyl (OctaBB)
– Nona Bromobiphenyl (Nonbaby)
– Hexabromobiphenyl (DecaBB)
| NA| NA| NA| Each 50 [f]| Sum 1000
8| Polybromo Diphenyl ethers (PBDEs)
– Bromodiphenyl ether (MonoBDE)
– Dibromodiphenyl ether (DiBDE)
– Tribromodiphenyl ether (TriBDE)
– Tetrabromodiphenyl ether (TetraBDE)
– Pentabromodiphenyl ether (PentaBDE)
– Hexabromodiphenyl ether (HexaBDE)
– Heptabromodiphenyl ether (HeptaBDE)
– Octabromodiphenyl ether (OctaBDE)
– Nonabromodiphenyl ether (NonaBDE)
– Decabromodiphenyl ether (DecaBDE)
| NA| NA| NA| Each 50 [f]| Sum 1000
9| Dibutyl phthalate (DBP)
Di-(2-ethyl hexyl) phthalate (DEHP) Benzyl butyl phthalate (BBP)
Di-(iso-butyl) phthalate (DIBP)
| NA| NA| NA| Each 50 [g]| Each 1000
NA = Not applicable [a] Test method with reference to IEC
62321-3-1:2013. [b] Test method with reference to IEC
62321-5:2013. [c] Test method with reference to IEC 62321-4:2013.
[d] Polymers and Electronic-Test method with reference to European
standard IEC 62321-7-2:2017. [e] Metal-Test method with reference
to European standard IEC 62321-7-1:2015. [f] Test method with
reference to European standard IEC 62321-6: 2015. [g] Test method
with reference to IEC 62321-8:2017.
Pb/Cd/Hg/Cr6+ Testing Flow Chart
PBBs/PBDEs Testing Flow Chart
Phthalates Testing Flow Chart
Unless otherwise stated the results shown in this report refer only to the sample(s) tested. This test report cannot be reproduced, except in full. Without prior written permission of the company,
Guangdong Safety Testing Co., Ltd.
No.1, the 1st North Industry Road, Songshan Lake Sci.&Tech. Park, Dongguan,
Guangdong, China
Tel:86-769-23105888 Fax: 86-769-22899858 http://www.sft-cert.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>