AViANCE HD29033 Delray 17 Inch 2 Light Brushed Nickel Vanity Light Instruction Manual

AViANCE HD29033 Delray 17 Inch 2 Light Brushed Nickel Vanity Light

Specifications:

• Model: HD29033
• Power Source: Electrical
• Material: Metal, Glass
• Maximum Wattage: Refer to fixture specifications

Product Usage Instructions

Assembling the Fixture:

1. Shut off the power at the circuit breaker box and remove the old fixture and hardware from the Junction Box.
2. Unpack the new fixture and lay out all parts in a clear area, ensuring not to lose any small parts.
3. Thread the mounting screws into the pre-drilled holes in the mounting plate and attach it to the junction box using junction box screws.
4. Guide fixture wires through the hole in the center of the mounting plate.
5. Follow wiring instructions carefully as shown in Fig.2.
6. Place the lamp body onto the mounting plate, aligning the holes with mounting screws, and secure it with the ball nut.
7. Attach the glass shade and cover to the socket holder and lock it securely with the ring until snug.
8. Install light bulbs (not included) according to the fixture’s specifications. Do not exceed the maximum wattage rating.

Connecting the Wires:

1. Connect the electrical wires by matching colors: black fixture wire to black house wire, white fixture wire to white house wire, and ground wires accordingly.
2. Secure all wire connections with wire nuts and consider wrapping them with electrical tape for added safety.
3. If your outlet box has ground wires, connect the fixture’s ground wire to it; otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
4. Tuck the wire connections neatly into the wall junction box.

FAQ:

Q: What should I do if I exceed the maximum wattage rating?
A: It is crucial not to exceed the maximum wattage rating as it can lead to overheating and potential hazards. If you require brighter lighting, consider using LED bulbs which consume less power but offer higher brightness levels.

Q: Can I use this fixture in a bathroom or outdoor setting?
A: It is recommended to check the fixture’s specifications for suitability in specific environments. Some fixtures are designed for indoor use only, while others are rated for damp or wet locations. Using a fixture in an unsuitable environment can lead to damage or safety issues.

Q: What should I do if I encounter difficulties during installation?
A: If you face challenges during installation, please reach out to our customer service at info@aviancelighting.net for assistance.
Our team is dedicated to helping you with parts or assembly queries.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
HD29033

ASSEMBLING & INSTALLATION INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

ASSEMBLING THE FIXTURE (Fig.1)

1. Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
3. Thread the two mounting screws into the pre-drilled holes in the mounting plate, spaced about the same distance apart as the holes in the fixture back plate. Attach the mounting plate to the junction box using two junction box screws as shown. The side of the mounting plate marked “GND” must face out. The junction box is not included.
4. Guide fixture wires through hole in center of mounting plate.
5. Follow wiring instructions carefully (see fig.2).
6. Place the lamp body(D) onto the mounting plate, aligning the holes with mounting screws, then lock it securely with the ball nut(E).
7. Raise the glass shade (C) and cover (B) to the socket holder, lock it securely with ring (A) until snug.
8. Install the light bulbs (not included) in accordance with the fixture’s specifications.

NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!

CONNECTING THE WIRES (Fig.2)

1. Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise attach the bare copper fixture wire to the green ground screw on the mounting plate.
2. Tuck the wire connections neatly into the wall junction box.

Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:info@aviancelighting.net

©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING,INC.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>