Summer Infant 27910 Banister and Stair Safety Gate Instruction Manual

June 15, 2024
Summer infant

Summer Infant 27910 Banister and Stair Safety Gate

WARNING

Children have died or been seriously injured when gates are not securely installed.

  • ALWAYS install and use gate as directed, using all required parts.
  • Install according to manufacturer’s instructions.
  • STOP using when a child can climb over or dislodge the gate.
  • Use only with the locking/latching mechanism securely engaged.
  • NEVER use a gate to keep child away from pool.
  • NEVER leave child unattended.
  • ALWAYS close and lock the gate behind you.
  • This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
  • Do not use if any components are missing or damaged.
  • Adult assembly required.
  • Exercise care when unpacking and assembling product.
  • Intended for use with children from 6 months through 24 months.
  • Do not mount to spindles less than 2 in. in diameter.
  • Check daily that banister brackets are securely attached and gate is securely anchored to banisters and/or wall.

Components

Hardware

Tools required (not included)

Phillips head Screwdriver

  • WALL MOUNT OPTION ONLY: Drill with 7/32″ drill bit
  • WOOD MOUNT OPTION ONLY: Pre-drill with 1/8″ drill bit

Maintenance

  1. Regularly check bolts and hinge assembly to ensure the gate is securely in place.
  2. Do not use gate if any components are damaged or missing.
  3. Wipe surface with a damp cloth or sponge using mild detergent and warm water.

Gate fits openings 33″ to 46″ (84 cm to 117 cm) (!)

IMPORTANT Place ter gas in a be pline a lie on the size from the end of the stairs or the furthest it can be placed based on the size and locations of your banisters.

Hinge Assembly

CHOOSE WHICH OF THE TWO OPTIONS WITHIN THE HINGE ASSEMBLY SECTION BEST FITS YOUR NEEDS.

Option A:
Square Top Banister (No drilling necessary)

IMPORTANT NOTE:
The’s are extra mostictio the metal hinge assembly in order to protect the wood of your banister.
Peel and stick the back of the metal hinge assembly before assembling onto the banister.
The pad is intended to help position the metal hinge bracket so that it is on a flat surface.

Option B:

Latch Assembly

IMPORTANT: Be sure to install the door stopper when using at the top of stairs! It should stop the gate from going over the stairs.

Support Foot Assembly:

IMPORTANT NOTE: Adjust foot to be just touching floor when gate is locked closed.

Door Assembly

SAFETY
WARNING
If installing gate at top of stairs,DO NOT mount into wallboard.

IMPORTANT

NOTE: When mounting into any wood (molding), a pre-drilled hole is required.
Pre-drill a hole in the wood,using an 1/8′ or 3mm drill bit approximately 1 inch deep.

Latch Assembly is identical to Hinge Assembly. Choose which of the two options best fits your needs.

Door Stopper

Gate Assembly

While the gate is off the wall or banister mounts, use the wrench to tighten or loosen the bolt to extend the gate to reach the latch.
Depending on your wall you may need to adjust the top and bottom bolts to make sure the gate is aligned properly and reaches the latch assembly.

IMPORTANT NOTE:

  • Never exceed 3 for a gap on hinge side or bottom of gate.
  • Gate can be horizontally leveled by rotating upper or lower adjustment nut (in or out) with supplied Wrench.

Operating Instructions

CLOSING THE GATE:

Please read the following instructions and warnings carefully.
Keep this instruction manual and save for future reference.

For technical support contact us at 1-401-671-6551 or www.summerinfant.com/contact.

For use with children from 6 to 24 months.

Adult assembly required.
Keep small parts away from children.

Summer Infant (USA), Inc. 1275 Park East Drive Woonsocke RI 02895 USA
1-401-671-6551
© 2019 Summer Infant {USA), Inc.

Colors and styles may vary.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals