DELTA DORE 620 Thermostats Dambiance Driver Instruction Manual

DELTA DORE 620 Thermostats Dambiance Driver

Product Information

The Pack DRIVER 620 RADIO/FP is a programmable radio thermostat with 2 zones. It is designed for use with the RADIO DRIVER system and can be fixed in place using screws.

Product Usage Instructions

Mise en service
To start using the thermostat:

1. Position the thermostat on its base
2. Lock the thermostat in place

Fixation par vis
To fix the thermostat using screws:

1. Use the provided screws and wall plugs
2. Connect the blue wire to N (neutral) and the brown and black wires to L (line)

Configuration

To configure the thermostat:

1. Press and hold the menu button for 3 seconds
2. Press the menu button to enter the menu
3. Turn the dial to navigate through the menu options
4. Press and hold the menu button for 5 seconds to save changes

Menu Options

The thermostat offers various configuration options:

• Configuration de base (Menu 1)
• Association radio (Menu 4)
• Version de l’appareil (Menu 6)
• Choix du type de fil pilote (Menu 9)
• Choix du type de programmation (Menu 11)
• Pas de programmation (Menu 11)
• Autorisation de modification (Menu 11)

Quitting the Menu
To exit the menu, turn the dial to the right.

Specifications

• Type: Programmable radio thermostat
• Zones: 2
• Fixation: Screw mount

conditions

Initial Setup and Placement of Radio Driver Transmitter

• Ensure the device is installed according to standards.
• For any intervention, turn off the power.
• Do not attempt to open or repair the device.
• Check the wall socket type and ensure it is compatible with the device.
• Use the provided screws and dowels for wall mounting.
• To put the device into service, remove the protective legs.

Mounting and Service Activation

• Mounting on the support and locking the thermostat.
• Connection behind the connector with clear indications for the antenna, connector, and pilot wire.
• Wire color coding for the connection: Blue (N), Brown (L), and Black (Pilot wire).

Associating Radio Driver Transmitter with RF 660 Receivers

1. Zone 1 Receiver Association
   • Press and hold the button for approximately 3 seconds.
   • Follow the instructions displayed on the Radio Driver for association.
2. Zone 2 Receiver Association
   • Repeat the above steps, ensuring the devices for zone 2 are in association mode.
3. Zone 3 Receiver Association
   • Same instructions as above for zone 3 devices.

Exiting Association Menu

• To exit the radio association menu, turn the dial to the right.

Basic Configuration (Menu 1)

• Adjusting days, minutes, and hours.
• Setting programming type and pilot wire configuration.

Advanced Configurations (Menu 2)

• Modifying program authorization and fil pilote order during Economy mode.

Factory Reset, Deleting Associations, and Radio Test

• Instructions for returning to factory settings, canceling all radio associations, and performing a radio test.

Configuration Table

• Detailed table explaining different configuration settings.

Troubleshooting

• Steps to help if encountering issues with the boiler or the pilot lights.

Technical Characteristics

• Technical specifications for Radio Driver and RF 660 including power requirements, consumption, and environmental conditions.

FAQ

How many zones does the thermostat support?

The thermostat supports 2 zones.

How do I fix the thermostat in place?

You can fix the thermostat in place using screws.

How do I configure the thermostat?

To configure the thermostat, press and hold the menu button for 3 seconds, then use the dial to navigate through the menu options. Press and hold the menu button for 5 seconds to save changes.

What are the available menu options?

The thermostat offers various menu options, including configuration de base, association radio, version de l'appareil, choix du type de fil pilote, choix du type de programmation, pas de programmation, and autorisation de modification.

How do I exit the menu?

To exit the menu, simply turn the dial to the right.

How do I mount the Radio Driver onto the wall?

You can mount the Radio Driver using the provided screws and dowels or by using the double-sided adhesive tape.

What should I do if the pilot wire colors do not match?

Ensure to connect the wires according to the designated color coding: Blue (N), Brown (L), and Black (Pilot wire).

How do I associate the Radio Driver with RF 660 receivers?

Press and hold the button for approximately 3 seconds to enter association mode, and then follow the on-screen instructions for each zone.

Can I reset the Radio Driver to factory settings?

Yes, you can reset to factory settings by following the instructions in the manual under the section Return to factory configuration.

How do I perform a radio test?

To perform a radio test, refer to section 11 Test radio in the manual for detailed instructions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>