SKYDANCE ES-D Stair Light Controller Instruction Manual

SKYDANCE ES-D Stair Light Controller

Product Information

Specifications

• Input voltage: 5-24VDC
• Input current: 8A
• Output signal: 2XSPI(TTL)
• Pixel number: Max 960 PIR sensor + Push button
• Warranty: 5 years
• Sensitive field: Ta:- 30°C to +55°C
• Sensitivity angle: Tc:+65°C
• Environment: IP20
• EMC standard (EMC): ETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4
• Safety standard: EN 62368-1:2020+A11:2020 CE, EMC
• Package Size: L175 x W120 x H35mm
• Gross weight: 0.27kg

Product Usage Instructions

Stair Light Application – PIR Sensor Control
To control the stair lights using a PIR sensor, follow these steps:

1. Connect the UP PIR sensor to the UP PIR sensor input.
2. Connect the DW PIR sensor to the DW PIR sensor input.
3. Connect the Daylight sensor to the LUX DET input.
4. Connect the power supply (5-24VDC) to the 5-24VDC INPUT.
5. Connect the RGB or white LED pixel strip to the SPI OUTPUT.
6. Configure the desired color or white light flow using the PIR sensor and push button input.

Stair Light Application – Step Control
To control the stair lights using step control, follow these steps:

1. Connect the UP PIR sensor to the UP PIR sensor input.
2. Connect the DW PIR sensor to the DW PIR sensor input.
3. Connect the Daylight sensor to the LUX DET input.
4. Connect the power supply (5-24VDC) to the 5-24VDC INPUT.
5. Connect the RGB or white LED pixel strip to the SPI OUTPUT.
6. Configure the desired color or white light for each step using the PIR sensor and push button input.

Sequential Switching Control
To connect one push switch with multiple controllers for sequential switching control, follow these steps:

1. Connect the push switch to the PUSH INPUT.
2. Connect the power supply (5-24VDC) to the 5-24VDC INPUT.
3. Connect the SPI OUTPUT of each controller to the SPI INPUT of the next controller.
4. Configure the desired sequential switching control using the push switch.

Frequently Asked Questions (FAQ)

• What is the input voltage range for the product?
  The product supports an input voltage range of 5-24VDC.

• What is the warranty period for the product?
  The product comes with a 5-year warranty.

• What are the operating temperature limits for the product?
  The product can operate in temperatures ranging from -30°C to +55°C.

• What is the IP rating of the product?
  The product has an IP20 rating.

INTRODUCTION

• Dual PIR sensor + dual push button input RGB or white light SPI controller features daylight sensor.
• Two groups same SPI(TTL) signal output, drive 28 kinds IC digital RGB or white LED strip, IC type and R/G/B order can be set.

Compatible ICs:
TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912, UCS2903,UCS2909, UCS2912, WS2811, WS2812, TM1829, TM1914A, GW6205,GS8206,GS8208,LPD6803, LPD1101, D705, UCS6909, UCS6912, LPD8803,LPD8806, WS2801, WS2803, P9813, SK9822, SM16703P.

• When applied to stair light, supports four output modes: color flow, white flow, color step, white step.
• Sequential switching control is realized when multiple SPI controllers are connected to a single self-resetting push switch button.
• Multiple light colors and change types are selectable with adjustable speed and brightness.

Technical Parameters

• Input and Output
  • Input voltage 5-24VDC
  • Input current 8A
  • Output signal 2XSPI(TTL)
  • Pixel number Max 960
  • Input signal PIR sensor + Push button
• Warranty
  • Warranty  5 years
• Sensor data
  • Sensitive field <3m
  • Sensitivity angle 309÷10°1
• Environment
  • Operation temperature Ta: -30°C ~ +55°C
  • Case temperature (Max.) Tc: +65°C
  • IP rating IP 20
• Safety and EMC
  • EMC standard (EMC)
  • ETSI EN 301 489-1 V2.2.3
  • ETSI EN 301 489-17 V3.2.4
  • Safety standard EN 62368-1:2020+A11:2020
  • Certification CE, EMC
• Package
  • Size L175 × W120 x H35mm
  • Gross weight 0.27kg

Mechanical Structures and Installations

Wiring Diagram

1. Stair light application, connect with PIR sensor, color or white light flow control

2. Stair light application, connect with PIR sensor, color or white light step control.

3. One push switch connect with multiple controllers for sequential switching control

Note:

1. If the SPILED strip is a single-wire control method, the DATA and CLK signal line outputs of the controller are same, and one controller can connect four LED strips.
2. If the SPI LED strip is a dual-wire control method, one controller can connect two LED strips.
3. When the SPI strip load does not exceed 15A, the same power supply can simultaneously power the ES-D controller and the SPl strip at the same time. When the load on the SPl strip exceeds 15A, separate power supplies are required for the ES-D controller and the SPI strip. Only DATA and GND signal lines are connected between the ES-D controller and SPI strip.
4. The PIR sensor can be replaced with a stair infrared reflection sensor(ES-T) or other sensors that output 5V level signals.
5. The color or white light flow model can control up to 960-pixel points of the SPI strip.
6. The color or white light step model defaults to 30 steps with 10 pixels per step. the step number x pixel length per step must < 960.

System Parameters Setting

• Press and hold the M and key for 2s simultaneously, and enter the system parameters setting state: set the light type, LED strip connection method (flow or step) pixel point number, step number, light on/ off mode, turn off light delay time, daylight detection, push switch to turn on or off the light delay time.
• Press and hold the M and key for 2s simultaneously, and enter the LED light strip parameters setting state: set the chip type, and RGB color order.
• In the parameter setting state, short-press press M key to switch multiple parameter items, and press or key to adjust the parameter value of each parameter item.
• Press and hold the M key for 2s or wait for 15s, quit the parameter setting state.
• Long press and key for 2s simultaneously, restore factory default parameters, and display “RES”. Factory default parameters: RGB color light flow output, 300 pixels, sequential light on, sequential light off, 30s delay off time, disable daylight detection, push switch turn-on delay and turn off delay is Os, chip type TM1809, RGB order.
• Light type: Set three light types.
  • 3-bead white light: 1 pixel with 3 same data, control 3-bead white LED, display “1-1”.
  • 1-bead white light: 1 pixel with 1 data, control 1-bead white LED, display “L-2”.
  • RGB color light: 1 pixel with 3 data, control one R/G/B LED, display “L-3”.
• Output mode: Set up flow or step output.
  • Flow: Straight line digital pixel LED strip light mode, display “o-l”.
  • Step: Z-shape digital pixel LED strip light mode, display “o-S”.
• Pixel dots: For color or white flow mode, set the number of pixel points, the range is 032-960, and display “032′-“960”.
• Step numbers: For color or white step mode, set the number of steps and pixel dot number of each step.
  • Step number: the range is 8-99, display “S08” or “599”;
  • Pixel dot number of each step: the range is 2-99, display “LO2”-“199”. the step number x pixel dot number of each step number must € 960.
• mode light: Set how the light turns on when the sensor is activated and the self-reset button turns on the light.
  • Sequential light on Light turn on sequentially from the beginning to the end, displaying “onS”.
  • Synchronized light on: Light turn on synchronously, display “onC”
• Light off mode: Set how the light turns off when sensing ends and when the self-reset button turns off the light.
  • Sequential light off: Light turns off sequentially from the beginning to the end, displaying “oFS”.
  • Sequence light off in reverse: Light turn off sequentially from end to beginning, display “oFb”.
  • Synchronized light off: Light turn off synchronously, display “oF”

List of ways to turn on/off light combinations:

• Sensor light off delay: Set the time delay for turning off the light at the end of sensing:
  5sec (d05), 10sec (d 10), 30sec (d30), 1 min (01d), 3min (03d), 5min (05d), 10min (10d), 30min (30d), 60min (60d), cancel (dOO), Set cancel means not turn off the light.

• LUX detection: Set the daylight detection on “Lon” or off “Lof”. When daylight detection is on, PIR sensing turns on light only when the ambient light is low.

• Self-reset push switch turn on light delay time: Setting range 0-15.5s, the smallest unit 0.5s, display “000”-“095”-“OF5”, A-F indicates that 10-15s. Setting Os means turning on the light immediately.

• Self-reset push switch turn off light delay time: Setting range 0-15.5s, the smallest unit O.5s, display “o00*”095”-“oF5”, A-f indicates that 10-1 5s.
  Setting Os means turning off the light immediately.

• Chip type: Select the chip type of the LED strip(shown in below table), display “C 1 1”-“C25”.

• RGB color order: Select 6 RGB orders (RGB, RBG, GRB, GBR, BRG, BGR), display “0-1” – “0-6” respectively.

LED strip IC types list:

Light effect settings

Color Flow/Color Step Mode

• The digital tube display “PO1 “”P95”, the 2nd digit indicates the light color, the 3rd digit indicates the type of light change.
• Short press key to switch 10 light colors in sequence, the 2nd digit shows 0-9. The Oth color light color can be customized, the 1 st-/th color light is single color, and the 8th-9th color light is multi-color.
• Short press key to switch 5 light change types in sequence, the 3rd digit shows 1-5.
• The light color and light change type are combined to form 50 kinds of light effects, each light effect can be adjusted in speed and brightness.
• Long press the M key for 2s to enter the light effect parameter setting state, set speed, brightness, and self-defined R/G/B color.
• Short press the M key to switch multiple parameter items, and press or key to adjust the parameter value of each parameter item.
  • Speed: 1-8 levels adjustable, display “S-1”-“S-8”, S-8 is the maximum speed.
  • Brightness: 1-10 level adjustable, display “b 10”-“bFF”, bfF means maximum brightness 100%.
  • Self-defined R/G/B color: 0-255 (00-FF) adjustable. R channel displays “100”-” 1 FF”; G channel displays “200” – “2FF”; B channel displays “300”-“3FF”
• Press and hold M key for 2s or wait for 15s, quit the light effect parameter setting

White Flow/White Step Mode

• The digital tube display “P-1″‘”P-5”, the 3rd digit indicates the type of light change.
• Short press or key to switch 5 light change types in sequence, the 3rd digit shows 1-5.
• Each lighting effect can be adjusted for speed and brightness.
• Long press the M key for 2s to enter the light effect parameter setting state, set speed, and brightness.
  • Short press the M key to switch multiple parameter items, and press or key to adjust the parameter value of each parameter item.
  • Speed: 1-8 levels adjustable, display “S-1″”S-8”, S-8 is the maximum speed
  • Brightness: 1-10 level adjustable, display “blO”-“bFF”, bFF means maximum brightness 100%.
• Long press the M key for 2s or wait for 15s, quit the light effect parameter setting.

Typical application

Dual PIR sensing control

• Connect two PIR sensors to realize automatic staircase light control.
• The UP PIR sensor is installed at the bottom of the staircase, when sensing a person, the digital tube instantly displays “u”, the light is automatically turned on, and the light is turned off with a delay.
• The DW PIR sensor is installed at the top of the staircase, when sensing a person, the digital tube instantly displays “-d”, the light is automatically turned on, and the light is turned off with a delay.
• If you set the daylight sensor detection on, the light will be turned on only in darker environments or at night.

Dual self-reset push switch manual control

• Connect two push switches for manual staircase light control.
• The UP push switch is installed at the bottom of the stairs; the DW push switch is installed at the top of the stairs.
• Set the self-reset push switch to Os for both light on delay and light off delay. short press the self-push switch to turn on the light, and display the current light effect mode; short press the self-push switch again, turn off the light, and display “OFF”.
  Long press the UP self-reset push switch to adjust the brightness, range 10-100%, and display “b 10”-“bFF”.
  (Note: The DW self-reset push switch does not have the function of adjusting the brightness.)
  Note: Using the self-reset push switch control will ignore the daylight sense detection.

Self-reset push switch connects multiple controllers for sequential switching control

• Multiple controllers are connected to one push switche at the same time to realize sequential switching control.

• Set the self-reset push switch on delay and off delay set 1-4# controllers’ light on delay to Os, 1s, 25, 3s
  In this way, 1-4# controllers will turn the lights on in

• Short press the self-reset push switch to turn on the li
  When the light is turning on, display the current lig

• Short press the self-reset push switch again to turn o
  When the light is off, display “OFF”
  Note: When the lighting effects of multiple controllers

Installtion of PIR sensor

Size of detector:

PIR sensor detection scope (# 10° Error):

Notice for installation of PIR sensor

• Recommended for wall mounting.
• If the sensor is exposed to direct sunlight, interference signal will be introduced.
• The sensor should be installed in a dry environment and kept away from windows, air conditioners, and fans.
• Make sure that the sensor stays away from heat sources, such as countertops, kitchen appliances that generate hot steam, walls and windows in direct sunlight, air conditioners, heating, refrigerators, stoves, and so on.
• We recommended the wall-mounted installation height is 1-1.5 meters and the ceilling mounting height is no more than 3 meters.
• There should not be shelter|screen, furniture, large bonsai) within the range of detection.

Packing List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>