TESLA M325 Smart 43 Inch Full HD TV User Guide
- October 30, 2023
- Tesla
Table of Contents
M325 SMART
43 Inch Full HD TV
QUICK START GUIDE
OPERATING INSTRUCTION
Please read these instructions before operating your set and retain them for
future reference.
WARNING AND PRECAUTIONS
Warning: To avoid the risk of electric shock, do not removecover (or
back). No user-serviceable parts inside.
Refer servicing to qualified service personnel.
| The lightning flash with arrowhead symbol, within an equilateral triangle is
intended lo alert the user lo the presence of uninsulated “dangerous voltage”
within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to a person.
---|---
| The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING
THE USE OF THIS UNIT.
- Operate only from the power source specified on the unit.
- Avoid damaging the AC plug and power cord.
- Avoid improper installation and never position the unit where good ventilation is unattainable.
- Do not allow objects or liquid into the cabinet openings.
- In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.
- When you don’t use this TV set for a long period of time, be sure to disconnect both the power plug from the AC outlet and antenna for your safety.
- To prevent electric shock do not use this power plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.
Do not attempt to service the product yourself
CAUTION!
To prevent electrical shock, do not open the TV casing.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
IMPORTANT SAFETY INSTRUCTIONS
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this unit near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths, curtains etc. There must be a minimum distance of 5cm clear space around the unit at all times to ensure proper ventilation.
-
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. No naked flame sources such as lit candles, should be placed on or near the unit.
-
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the unit.
-
Only use attachments/accessories specified by the manufacturer.
-
Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the unit. When a cart is used, use caution when moving the cart/unit combination to avoid injury from tip-over.
-
Unplug this unit during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the unit, the unit has been exposed to rain or moisture, does not operate normally or has been dropped.
-
The unit should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on the unit.
-
Place the television on a stable, flat surface. Failure to do so can result in the television falling, causing injury.
-
Do not allow young children to play around or on the television. Do not hang from the unit Failure to do so can result in the television falling, causing injury.
-
Do not allow young children to play with the plastic bag that came with the television when you unpacked it.
Failure to do so can result in suffocation, which may lead to death. -
Avoid improper installation and never position the unit where good ventilation is impossible. When installing this unit, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation.
-
Cautions for installation
– Do not tilt the unit towards the left or right or towards the back.
– Ensure the power cord is out of the path of foot traffic.
– The unit will generate a slight amount of heat during operation. Ensure that sufficient space is available around the unit to allow satisfactory cooling.
– Have two people remove the unit from the box with the screen facing away from you. It’s possible your clothing (such as a belt buckle or button) may scratch the front of the unit. Do the same when moving the unit to another location. -
This unit shall be connected to a mains socket outlet with a protective earthing connection.
-
Make enough room for inserting and removing the power plug. Place the unit as close to the outlet as possible. The main power supply for this unit is controlled by inserting or removing the power plug. Physically disconnecting the power plug is the only way to completely disconnect the unit from the mains power source.
-
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
-
When this unit is connected to the wall outlet, it is always on standby even when all the LED lamps are not lit. To shut down the unit, unplug the unit from the wall outlet.
-
If the supply cord is damaged, it must be replaced before further use by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
-
Always place the TV on furniture that can safely support the TV. Make sure the ends of the TV do not overhang the edge of the supporting furniture.
-
Do not place the TV on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the TV to a wall or other suitably strong support.
-
Do not stand the TV on cloth or other materials placed between the TV and the supporting furniture.
-
Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
Important information
Televisions that are not positioned in sufficiently stable locations can
present potential falling hazards. To avoid injuries, particularly to
children, take the following simple precautions:
- Place this television only on furniture that can safely support it.
- Use only a cabinet or stand recommended by the manufacturer of the television.
- Ensure the television does not hang over the edge of supporting furniture.
- Do not place the television on tall furniture (such as cupboards or bookcases) without anchoring both the furniture and the television to a suitable support.
- Do not place cloth or other materials between the television and the supporting furniture.
- Do not let children climb on furniture to reach the television or its controls.
REMOTE CONTROL OPERATION
Installing Batteries
- Slide in the direction shown by the arrow in Image 1 below to open the cover of the batteries on the back of the remote control.
- Load two AAA alkaline batteries in the compartment.
- Replace the cover of the batteries.
Precautions
- Make sure that there is no obstacle bet ween the remote control and television set.
- Keep the remote control away from heat sources and humid areas to ensure effective performance of the remote control.
- As strong light may interfere with the signals, change your position to operate the remote control if the television cannot be turned on or off as you excpect.
- Make sure that two AAA 1.5V alkaline batteries are loaded correctly.
TERMINAL INTERFACE
| AV input
External AV Signal Input And Relevant Right/Left Sound Channel
---|---
| AV output
TV AV Signal output And Relevant Right/Left Sound Channel (Some models without
this interface)
| Y Pb Pr input
Connect to the composite terminal of yourDV D/VCR (Some models without this
interface)
| HDMI input
Digital signal input from HDMI video connector.
| ANT75
Connect the antennal/cadle tv input (75NHF/UHF)
| VGA input
PC analog signal input
| PC AUDIO INPUT
VGA input and audio input when VGA input
| EARPHONE output
When earphones are plugged in, speakers are disabled (Some models without this
interface)
| USB input
Connect a USB device here to play its media files
| COAXIAL
Connect the SPDIF receiver. (Some models without this interface)
| SCART input
Standard, it supports composite and RGB signal input.It is a connection for
european (Some models without this interface)
| Cl
Connect the Data TV decryption card
REMOTE CONTROL
POWER ( ): Turns the TV on or off.
INPUT: To select input source menu.
NUMBER BUTTONS: Press 0-9 select a TV channel directly when you are
watching TV.
GUIDE: Shows Electronic Program Guide.
CH.LIST: Access the channel list.
RED/GREENNELLOW/BLUE: Use add-on functions in OSD menu.
MENU ( ): Accesses the Main Menu.
: play or pause media files.
Arrows ( ): Uses the four arrows to highlight different items in the TV
menu or change the value.
OK: Enter and confirm button.
( ): Returns to the previous channel.
EXIT: Exits the current menu or function.
VOL+ or VOL-: Increases or decreases the TV volume.
HOME ( ): Press to open home page.
MUTE ( ):Mute or restore the TV sound
CH or CH : Scans up or down through the current channel list
TEXT: To enter Teletext mode.
SUBTITLE: Press to enable or disable subtitles.
INFO: To display the current program information on the screen.
APP: Quick access to the app
: Custom button to launch input or apps quickly
APP: Quick access buttons to apps
MEDIA: Enter the media mode
BROWSER: Enter into BROWSER
NOTE:
All pictures in this manual are examples, only for reference, actual product
may differ from the pictures.
FIRST TIME INSTALLATION
Please according to the Text Tip to First Time Setup. Press ▲/▼ button to
select Language & choose TV Mode.
After setup language ,you can enter the Internet
setup page,please confirm and connect the internet. Select the country you
want .confirm and enter the next page.
Press [ ▲/▼ button to select the corresponding privacy
notice/terms and conditions, and press OK button to go to next step.
Sign
in your VIDAA account. If you haven’t created an account,please create an
account first and then sign in.
Choose the NETFLIX or enter the Smart
TV.
Please
make sure the device has connected, then press ▲/▼/◄/► button to select
the primary input source
HOME
When finish First Time setup,you can enter HOME screen.
Press MENU button to select HOME screen.Press ▲/▼/◄/► button to select. Inputs: Icon to select an
input source.
Setting: Various settings can be configured here.
INPUT
Press ▼/▲ button to select Inputs menu.
Press ▼/▲/◄/► button to select.
Press ENTER to select input.
MAIN MENU OPERATION
Picture
Press [MENU] to enter the main menu, press ▼/▲ to select picture menu ,
- Press ▼/▲ button to select the option that you want to adjust in the PICTURE menu.
- Press Enter button to adjust.
- After finishing your adjustment, Press Enter button to save and return to the previous menu.
Picture Mode
Press ▼/▲ button to select Picture Mode, then press ▼/▲ & Enter
button to select. (Optional: Standard/ Cinema day/Cinema
night/Dynamic/Sports).
Standard: The default mode, to make users experiencehigh-quality images
under normal light.
Cinema day: Enhance the contrat, color and clarity of the screen to make
the color more vivid.
Cinema night: Reduce the screen contrast, coIorand clarity to make the
screen looks soft.
Dynamic: Enhance the contrast,color and clarity of the screen, so that
the picture in the dynamic will balance the color.
Sports: This mode is more suitable for watching sport video.
Aspect Ratio
Adjust the Aspect Ratio to stretch or zoom in on your picture.
Press ▼/▲ button to select Aspect Ratio.
Press ◄/► button to select Automatic/16:9/4:3/
Panoramic/Movie Zoom/Direct.
Game Mode
Press ▼/▲ to select,and press ◄/► to select On/Off.
Picture Mode Settings
Press ▼/▲ to select,and press ► & ENTER to enter.
Apply Picture Settings
In this menu.you can adjust current picture mode to apply to all sources or
just current source. Press ▼/▲ to select,and press ► & ENTER to
enter. (Optional: AII Sources/Curremt Source)
Backlight/Brightness/Contrast/ColourSaturation/ Sharpness
Press ▼/▲ to select,and press ◄/► to adjust.
Backlight: Adjust image backlight.(OptionsI:Off/Low/High)
Brightness: Adjust image brightness.
Contrast: Adjust image contrast.
Colour Saturation: Adjust image color density.
Sharpness: Adjust the image edge sharpness.
Colour Tuner
Adjust the Hue,saturation and Brightness of color srttings.
Press ▼/▲ button to select Colour Tuner.
Press ◄/► button to enter sub-menu and adjust.
White Balance
Adjust the intensity of red,green and bule lights to view the ture colors of
all images in the picture. Press ▼/▲ button to select White Balance. Press
◄/► button to enter and adjust.
Black Level (Only available on HDMI source)
In this menu,you can adjust the HDMI signal range to
be more suitable for content.
Press ▼/▲ to select Black Level, press ◄/► to select.
Gamma Adjustment
Press ▼/▲ to select Gamma Adjustment.
Press ◄/► to select 2.0/2.2/2.4/BT.1886.
Gamma Calibration
In this menu,you can adjust the Gamma curve which one you selected.
Press ▼/▲ to select Gamma Calibration.
Press ◄/► button to enter sub-menu to adjust.
RGB Only Mode
Press ▼/▲ to select RGB Only Mode .
Press ◄/► to select Off/Red/Green/Blue.
Low Blue Light
Press ▼/▲ to select Low Blue Light.
Press ◄/► to select Off/Low/Middle/High/Very High.
Overscan
Press ▼/▲ button to select Overscan.
Press ◄/► button to select On/Off.
Reset Current Mode
Press ▼/▲ button to select Reset Current Mode.
Press ◄/► button to enter sub-menu.
Sound
Press MENU button to display the main menu. Press ▼/▲ button to select
SOUND in the main menu,
- Press ▼/▲ button to select the option that you want to adjust in the SOUND menu.
- Press Enter button to adjust.
- After finishing your adjustment, Press Enter button to save and return to the previous menu.
Sound Mode
Press ▼/▲ button to select your favorite Sound Mode.
(Optional: Standard/Theatre/Music/Speech/Late Night/ Sports.)
Standard: Produces a balanced sound in all environments.
Theatre: Theatre mode increases the surround sound effect and provides a
more prominent subwofer response.
Music: Preserves the original sound.Good for musical programs.
Speech: Low and high frequencies are attenuated to improve the
reproduction and clarity of the human voice.
Late Night: Improve the reproduction and clarity of the human voice with
a low volume level.
Sports: Optimised sound for watching football game.
Headphone
Press ▼/▲ button to select Headphone.lt only available on headphone is
inserted. It can set the sound output mode through headphones.
Sound Mode Settings
Press ▼/▲ button to select Sound Mode Settings. Press ◄/► button to
enter sub-menu.
Apply Audio Settings
Adjust the Curren sound mode to apply to all source or just current source.
Press ▼/▲ button to select, then press ► & Enter button to select
Current Source/AII Sources.
Equalizer
Press ◄/► button to select.and adjust Equalizer detail
(Optional:100Hz/500Hz/1.5KHz/5KHz/10KHz)
Bass Boost/Surround Sound/Dialog Clarity/ TruVolume/Wall Mount
Setup/Auto Volume Control
Press ▼/▲ button to select, and press ◄/► button to select On/Off.
Reset Current Mode
Press ▼/▲ button to select, a nd press ◄/► button to choose restore or
not.
Speakers
Press ▼/▲ button to select Speakers.
Press ◄/► button to enter sub-menu.
Audio Output
Press ▼/▲ button to select Audio Output and enter, then press ▼/▲
button to select ARC/TV Speaker/ SPDIF Only.
Digital Audio Output
Press ▼/▲ button to select Digital Audio Out, then
press ▼/▲ button to select.
Digital Audio Delay
Press ▼/▲ button to select Digital Audio Delay, then
press ▼/▲ button to adjust.
Lip Sync
Press ▼/▲ button to select, then press ◄/► button to adjust.
Balance
Balanced left and right channels.
Press ▼/▲ button to select Balance. Press ◄/► button to adjust.
Network
Press MENU button to display the main menu. Press ▼/▲ button to select
Network in the main menu.
Press ▼/▲ button to select: Network Configuration/ lnternet Connection/
Wake on Wireless Network/Wake on LAN.
Network Cofiguration
Press ▼/▲ button to select Network Configuration to set up the network.
Internet Connection
Press ▼/▲ button to select Internet Connection to check Internet
Connection.
Wake on Wireless Network
Press ▼/▲ button to select Wake on Wireless Network, then press ◄/►
button to selece On/Off.
Wake on LAN
Press ▼/▲ button to select Wake on LAN. Press ◄/► button to select
On/Off.
Channel
Press MENU button to display the main menu. Press ◄/► button to select
Channel.
- Press ▼/▲ button to select the option that you want to adjust in the Channel menu.
- Press Enter button to adjust.
- After finishing your adjustment, Press Enter button to save and return to the previous menu.
Auto Scan
Automatic search can search for effective program channel automatically. Press
▼/▲ button to select Auto Scan, then press OK button to setup.
Rescan
In this page,you can choose rescan channel or change setup.
Reception
Press ◄/► button to select Reception,and press ▼/▲ button to select
Satellite/Antenna/Cable.
Operator
Press ◄/► button to select ,and press ▼/▲ button to setup.
Mode setup
Press ◄/► button to select Mode setup, and press ▼/▲ button to select
Channel/Scan Mode/LCN.
Auto Scan
If you want to stop searching, press Stop or Exit button to stop searching.
Channel Edit
Press ▼/▲ button to select Channel Edit.
Advanced Settings
Press ▼/▲ button to select Advanced Settings,then press Enter/ ►
button to enter.
Manual Scan
Press ▼/▲ button to select Manual Scan, then press Enter button to enter.
Press ▼/▲ button to select DTV Manual Scan/ATV Manual Scan.
DTV Manual Scan
Press ▼/▲ button to select DTV Manual Scan, then press Enter button to
enter.
ATV Manual Scan
Press ▼/▲ button to select ATV Manual Scan, then press Enter button to
enter.
Channel List Auto-Update
Press ▼/▲ button to select Channel List Auto-Update, then press ◄/►
button to select On/Off.
Programme Guide Auto Update
Press ▼/▲ button to select Programme Auto Update.
Programme Auto Update
Press ▼/▲ button to select Channel ListAuto-Update, then press ◄/►
button to select On/Off.
Channel Selection
Press ▼/▲ button to select Channel Selction.
CI+ Module Settings
Press ▼/▲ button to select CI+ Module Settings and you can review the
advanced settings menu.
Accessibility
Press ▼/▲ button to select Aaccessibility.then press Enter button to
enter.
Menu Scheme
Press ▼/▲ button to select Menu Scheme,then press ◄/► button to
choose Dark/Light.
High Contrast Menu
Press ▼/▲ button to select High Contrast Menu, then press ◄/► button
to select On/Off.
Menu Transparency
Press ▼/▲ button to select MenuTransparency, then press ◄/► button to
choose Off/Medium/High.
Hard of Hearing Subtitles
Press ▼/▲ button to select Hard of Hearing Subtitles, then press ◄/►
button to select On/Off.
Audio Type
Press ▼/▲ button to select Audio Type,then press Enter button to enter
sub-menu.
Audio Type
Press ▼/▲ button to select Audio Type, then press ◄/► button to select
Normal/Audio Description/ Spoken Subtitles/AII Supplementary Audio.
Voiceover Volume
Press ▼/▲ button to select Voiceover Volume^hen press ◄/► button to
select On/Off.
Dialogue Enhancement
Press ▼/▲ button to select Dialogue
Enhancement,then press Enter button to enter submenu.
System
Press MENU button to display the main menu.
Press ◄/► button to select System in the main menu.
- Press ▼/▲ button to select the option that you want to adjust in the System menu.
- Press Enter button to adjust.
- After finishing your adjustment, Press Enter button tosave and return to the previous menu.
Time
Press ▼/▲ button to select Time.
Time Format
Press ▼/▲ button to select Time Format.
(Optional: 12-hour/24-hour)
Date/Time
Set the Date and Time
Press ▼/▲ button to select.then press Enter/ ► to setup.
Time Zone
Select yourtime zone
Press ▼/▲ button to select Timer zone,then press Enter/ ► to enter
sub-menu to setup.
Daylight Savings
Press ▼/▲ button to select Daylight Savings.
(Optional:Off/On/Sync from DTV)
Timer Settings
Press ▼/▲ button to select Timer Settings.
Sleep Timer
Press ▼/▲ button to select Sleep Timer.
(Optional: Off/15/30/60/90/120 Minutes/User Defined)
Power On Timer
Press ▼/▲ button to select Power On Timer.
Power Off Timer
Press ▼/▲ button to select Power Off Timer.
Menu Timeout
Press ▼/▲ button to select Menu Timeout.
(Optional :0ff/10s/20s/30s/60s/5min)
Auto Sleep
Press ▼/▲ button to select Auto Sleep.
(Optional:Off/3H/4H)
Auto Standby with No Signal
Press ▼/▲ button to select Auto Stand by with No Signal.
(Optional:Off/15 Minutes)
System PIN
Press ▼/▲ button to select System PIN.
Change your PIN that you use to access Parental Controls, Auto Channel Scan
and Reset To Factory Defaults.
Parental Control
Press ▼/▲ button to select Parental Control.
Turn on Parental Controls to block children from being able to view certain
programmes.
Language and Location
Press ▼/▲ button to select Language and Location.
Turn on Parental Controls to block children from being able to view certain
programmes.
Location
Press ▼/▲ button to select Location,and press Enter/ ► to select.
Menu Language
Press ▼/▲ button to select Menu Language.and press Enter/ ► to select.
Primary Audio
Press ▼/▲ button to select Primary Audio,and press Enter/ ► to select.
Secondary Audio
Press ▼/▲ button to select Secondary Audio,and press Enter/ ► to
select.
Primary Subtitle
Press ▼/▲ button to select Primary Subtitle, and press Enter/ ► to
select.
Secondary Subtitle
Press ▼/▲ button to select Secondary Subtitle, and press Enter/ ► to
select.
Digital Teletext
Press ▼/▲ button to select Digital Teletext.
Optional: WEST EUR/EAST EUR/Russian/Aarabic/ Persian/Greek) button to select
Content Sharing. Then press ◄/► button to select On/Off.
Application Settings
Press ▼/▲ button to select Application Settings.
Content Sharing
Press ▼/▲ button lo select Content Sharing,lhen press ◄/► button lo
select On/Off.
HbbTV
Press ▼/▲ button to select Hbb TV,then press ◄/► button to select
On/Off.
Clear Cache
Press ▼/▲ button to select Clear Cache,then press ENTER/ ► button to
enter sub-menu.
Delete Cookies
Press ▼/▲ button lo select Delete Cookies,lhen press ENTER/ ► button
lo enter sub-menu.
Do Not Track
Press ▼/▲ button to select Do Not Track,then press ENTER/ ► button to
enter sub-menu.
Prime Video
Press ▼/▲ button to select Prime Video, and press Enter/ ► to select.
Netflix
Press ▼/▲ button to select Netflix, and press Enter/ ► to select.
HDMI &CEC
Press ▼/▲ button to select HDMI&CEC,then press Enter button to enter sub-
menu to select.
Press ▲ button to select CEC Control/Device Auto
Power Off/Device Auto Power On/ TV Auto Power On/ CEC Device Lists.
Note: All the Options are available only when the CEC Control select On.
CEC Control
Press ▼/▲ button to select CEC Control.and press ◄/► button to select
On/Off.
The following terms are available only when “On” is selected in CEC Control.
Device Auto Power Off
Press ▼/▲ button to select Device Power Off,and press ◄/► to select
On/Off.
Device Auto Power On
Press ▼/▲ button to select DeviceAuto Power On, and press ◄/► buttonto
select On/Off.
TvAuto Power On
Press ▼/▲ button to select TVAuto Power On, and press ◄/► buttonto
select On/Off.
CEC Device Lists
Press ▼/▲ button to select CEC Device Lists, and press ENTER button to
enter.
Usage Mode
Press ▼/▲ button to select Usage Mode, then press ENTER/ ► button to
select Home Mode/Store Mode.
Advanced Settings
Press ▼/▲ button to select Advanced Settings,then press ENTER/ ►
button to enter
TV Name
Press ▼/▲ button to select TV Name.then press ENTER/ ► button to setup
your TV name.
Power Indicatior
Press ▼/▲ button to select Power Indicatior,then press ◄/► button to
select On/Off.
Screen saver
Press ▼/▲ button to select Screen saver,then press ENTER/ ► button to
enter. (Optional:None/5 Minutes/10 Minutes/20 Minutes)
Input Labels
Press ▼/▲ button to select Input Labels,then press ENTER/ ► button to
enter. (Optional:TV/AV/HDMI1/ HDMI2/HDMI3)
Notifications
Press ▼/▲ button to select Notifications, then press ENTER/ ► button
to enter sub-menu and select.
Enhanced Viewing
Press ▼/▲ button to select Enhanced Viewing, then press ENTER/ ►
button to enter sub-menu and select.
Setup Wizard
Press ▼/▲ button to select Setup Wizard,then press ENTER/ ► button to
select.
Fast Power On
Press ▼/▲ button to select Fast Power On. Then press ◄/► button to
select On/Off.
Power On Mode
Press ▼/▲ button to select Power On Mode.then press ENTER/ ► button to
select.
Support
Press ▼/▲ button to select Support.then press ENTER/ ► button to enter
System Info
View System information
Press ▼/▲ button to select System Info,then press ENTER/ ► button to
enter sub-menu.
Self Diagnosis
Perform self diagnosis to test sound,pictureand connections.
Press ▼/▲ button to select Self Diagnosis.then press ENTER/ ► button
to enter sub-menu.
E-Manual
Press ▼/▲ button to select E-Manual, then press ENTER/ ► button to
enter sub-menu.
System Update
Set your TV to receive the latest firmware.
Press ▼/▲ button to select System Update, then press ENTER/ ► button
to enter sub-menu.
Disclaimer and Privacy
Click to read the Disclaimer details.
Press ▼/▲ button to select Disclaimer and Privacy, thenpress ENTER/ ►
button to enter sub-menu.
Mobile App Download
Press ▼/▲ button to select Mobile App Download, then press ENTER/ ►
button to enter sub-menu.
Restore To Factory Default
Press ▼/▲ button to select Restore To Factory Default, then press ENTER/
► button to enter sub-menu and select.
Press MENU button to wakeup Menu,then press ▼/▲ button to select.
Channel List
Press ▼/▲ button to select Channel List,then press ENTER button to enter
sub-menu.
Subtitle
Press ▼/▲ button to select Subtitle, then press ▼/▲ button to select
Off/On.
Audio Only
Press ▼/▲ button to select Audio Only. Press OK button enterthe sub-menu.
Settings
Press ▼/▲ button to select Settings. Press OK button enterthe sub-menu.
Please refer to the home page-Setting part
Guide
Press ▼/▲ button to select Guide, then press ENTER button to enter sub-
menu.
Subtitle
Press ▼/▲ button to select Subtitle, then press ▼/▲ button to select
Off/On.
Audio Only
Press ▼/▲ button to select Audio Only. Press OK button enter the sub-menu.
Settings
Press ▼/▲ button to select Settings. Press OK button enter the sub-menu.
Please refer to the home page-Setting part
HELP
| Problem | Solution |
|---|---|
| No Power | • Check the AC cord of TV is plus in or not. If still no power, |
please pull out the plug and replug in after 60 seconds. And open the TV again
Signal receive not properly| • To cause double image or phantom if there has
high building or high mountain round TV. You can adjust image effect by
manually operation: consult instruction of vernier regulation or change the
direction of external antenna.
• If you use the indoor antenna, under certain circumstance, receive will be
more difficult .So you can change the direction of the antenna to adjust the
image effect . If can’t change image receiving effect either , you have to use
external antenna.
No picture| • Check the antenna at the back of TV is connected properly or
not.
• Try to select other channels and check whether the TV problem itself or not
Video is ok without audio| • Increase the volume.
• Check the TV is in mute mode or not , and please press the mute button to
make sound resume.
Audio is ok color error or no picture| • Increase contrast and brightness.
Snow statics picture and noise| • Check the antenna at the back of TV is
connected or not.
Level broken line| • Vacuum, such as hair drier, Maybe has electrical
appliance interfere. Please turn off these kinds of electrical appliance,
cleaner and so on.
Image or-Dual “simulacrum” The TV no response with the Remote| • Perhaps the
location for the antenna is not good.Use the tall beamed antenna can be
improved quality of the display image.
• Operate the remote direct to the remote sensor on the TV.If still no
response for the TV, please check if the plastic bag on the remote take or
not. And check if the location for the battery is correct.Change the new
battery.
• The TV will shift to the STAND BY if no response from the remote in the few
minutes.
NO Video In (PC Mode)| • Please check if the display cable connect to the VGA
correcte.
• Please check if there has the bend on the display cabIe
Vertical twinkling (PC Mode}| • Enter the main menu . Use the clock regulator
for the video display noise to eliminate the vertical line.
Horizontal ripping (PC Mode)| • Adjust the Audio sound horizontal in the main
menu to clear the horizontal ripping line.
The screen is too bright or too dark (PC Mode)| • Adjust the contrast ratio or
brightness in the main menu.
PC Function no response| • Check the computer setting in the state of
compatible display resolution
Ripping line in RCA connecting| • Please use good quality connecting cable.
Problem still exist| • Unplug the power cable and wait for 30 seconds, then
connect. If there is some problem with our TV, do not repair it by yourself,
please contact with the customer service canter.
There will be complete picture and the brightness wi ll come down if the TV is
in Note. So please do not kee p the TV in a state of same, the static picture
for too long time. Menu or same picture that has much difference in brightness
and contrast ratio for too long time.
Note: TV panel is built with very high precision technology giving you
fine picture details in vibrant color. Occasionally, a few non-active pixels
may appear on the screen as fixed point of red,green,blue or white. Please
note this does not affect the performance of the product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>