SKYDANCE DA4-D 4 Channel Constant Voltage DALI LED Dimmer Instruction Manual

DA4-D 4 Channel Constant Voltage DALI LED Dimmer
Instruction Manual

DA4-D 4 Channel Constant Voltage DALI LED Dimmer

4 Channel Constant Voltage DALI LED Dimmer
Model No.: DA4-D
1-4 DALI address selectable/4 Channel/Constant voltage/PMW dimming/Numeric display/Din Rail

• 4 channel constant voltage DALI LED Dimmer with digital display, 5A per channel.
• 1-4 DALI address quantity is selectable, 4 channel work separately.
• In accordance with DALI standard protocol IEC 62386-102, IEC 62386-207 and in compliance with DALI productsfrom other international incorporation.
• DALI address can be manually assigned and shown in digital display or automatically assigned by DALI master.
• PWM digital dimming, standard DALI logarithmic dimming curve.
• PWM frequency 1000/2000/4000/8000Hz selectable.
• Over-heat / Over-load / Short circuit protection, recover automatically.
• With fast self-testing function.
• Available in white or black.

Technical Parameters

Input and Output

Input voltage| 12-24VDC
Input current| 20.5A
Output voltage| 12-24VDC
Output current| 4CH,5A/CH
Output power| 4 x (60-120)W
Output type| Constant voltage
Environment

Operation temperature| Ta: -30 O C ~ +55 O C
Case temperature (Max.| T c: +85 O C
IP rating| IP20
Dimming range| DALI
---|---
Input signal| 0 -100%
Dimming curve| Logarithmic
PWM Frequency| 1000/2000/4000/8000Hz

Warranty and Protection

Mechanical Structures and Installations

Wiring Diagram

Operation

Set DALI Address Quantity
You need set DALI address quantity according to applications requirement for the time.

• Long press M for 2s, prepare for set DALI address quantity.
• Short press ◀ or ▶ key to switch between1/2/3/4 DALI address quantity (”1CH”,”2CH” ,”3CH” or ”4CH”).
• Short press M key or timeout 10s, quit DALI address quantity setting.

DALI address quantity setup explain:
When set 1 DALI address, Ch1,Ch2,Ch3,Ch4 will be the same DALI address.
When set 2 DALI address, Ch1,Ch3 will be same DALI address A, Ch2,Ch4 will be same DALI address A+1.
When set 3 DALI address, Ch1 will DALI address A, Ch2 will DALI address A+1,
Ch3 will DALI address A+2, Ch4 no DALI address and no output.
When set 4 DALI address, Ch1 will DALI address A, Ch2 will DALI address A+1,
Ch3 will DALI address A+2, Ch4 will DALI address A+3.

For example, the start DALI address is 32:
When DALI address quantity is ”1CH”, the dimmer occupy 1 DALI address and address is 32.
When DALI address quantity is ”2CH”, the dimmer occupy 2 DALI addresses and address is 32,33.
When DALI address quantity is ”3CH”, the dimmer occupy 3 DALI addresses and address is 32,33,34.
When DALI address quantity is ”4CH”, the dimmer occupy 4 DALI addresses and address is 32,33,34,35.
Set DALI Address via buttons

• Long press ◀ or ▶ key for 2s, prepare for set the start DALI address, then press ◀ or ▶ key to set the start DALI address.
• Short press M key or timeout 10s, quit start DALI address setting.
• The start DALI address can be manually assigned from 00-63-FF.
• by factory defaults, no DALI address is assigned for the dimmer, and digital display shows “AFF”.

DALI address assigned by DALI masters
DALI address can also be assigned by DALI Master controller automatically.
Please refer to user manuals of compatible DALI Masters for speci
The digital display will show “AAU” When the DALI master is assigning address.
After address is assigned, the digital display will show the start DALI address”Axx”, xx is from 00 to 63.
Using DALI master assign address may result in discontinuous address, the digital display will show the start DALI address”Uxx”.

Set PWM frequency

• Long press M & ◀ key for 2s, prepare for set PWM frequency.
• Short press ◀ or ▶ key to switch between1000Hz(“F10”), 2000Hz(“F20”), 4000Hz(“F40”) or 8000Hz(“F80”). Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera (No flickers for video).
• Short press M key or timeout 10s, quit PWM frequency setting.

Restore factory default parameter

• Long press ◀ and ▶ key for 2s, restore factory default parameter, display ”RES”.
• Factory default parameter: no DALI address is assigned, DALI address quantity is 4, PWM frequency is 2000Hz.
• Long press M & ▶ key for 2s, enter fast self-testing, the output channel will be on orderly then all on.

Safety & Warnings

• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.

DA4-D 4 Channel Constant Voltage
DALI LED Dimmer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>