SKYDANCE V3-L WT WiFi and RF 3 in 1 LED Controller User Manual

SKYDANCE V3-L WT WiFi and RF 3 in 1 LED Controller User Manual

Features

• 3 in 1 function, used for control RGB, color temperature or single color LED strip.
• DC12-48V input, 3 channel constant voltage output.
• Tuya APP cloud control, support on/off, RGB color, color temperature and brightness adjust, delay turn on/off light, timer run, scene edit and music play function.
• Voice control, support amazon ECHO and Tmall Genie smart speaker.
• Match with RF 2.4G remote control optional.
• User need set light type by press key before Tuya APP network connection and match RF remote of the same light type.
• Each V3-L(WT) controller can also work as WiFi-RF converter, then use Tuya APP to control one or more RF LED controller or RF LED dimming driver synchronously.
• Light on/off fade time 3s selectable.
• Connect with external push key to achieve on/off and 0-100% dimming function.
• Logarithmic or linear dimming curve selectable.
• PWM frequency 500Hz, 2KHz, 8KHz or 16KHz selectable.
• Over-heat / Over-load / Short circuit protection, recover automatically.

Technical Parameters

Mechanical Structures and Installations

System wiring

Note:

1. The above distance is measured in spacious(no obstacle) environment, Please refer to the actual test distance before installation.
2. Please Check If The WiFi routernetin2.4Gband, the5Gband is not available, and don’t hide your router network.
3. PleasekeepthedistancebetweenV3-L(WT) device and router close, and check the WiFi signals.

Wiring Diagram

Note:

1. For CCT light type, continuous power on and off will change 3 levels color temperature (WW, NW and CW) in sequence.
2. Switch off the power, then switch on power, repeat again. Immediately short press match key 3 times, the light on/off time will change between 3s and 0.5s.

Tuya APP network connection

Press and hold Match key for 2s, or push twice Match key fatly, or when press and hold Match key + 1-3 Push key for 2s to set 3 kinds light type: Clear previous network connection, enter Smart config mode, the blue LED indicator flash fatly, the output LED will flash 10 times. Press and hold Match key for 5s: Clear previous network connection, enter AP config mode, the blue LED indicator flash slowly. If smart config failed, please try AP config. Repeat power on and off for 5 consecutive times, also clear previous network connection, enter Smart config mode, the output LED will flash 10 times. If Tuya APP network connection succeed, the blue LED indicator will stop flash, and in Tuya APP, you can find RGB device (or other DIM, CCT).

Tuya APP interface

The 1-4 scene is static color for all light type. the inner color of these scene can be editable. The 5-8 scene is dynamic mode for RGB type, such as green fade in and fade out, RGB jump, 6 color jump, 6 color smooth.
User Manual Ver 1.0.0

Push-Dim control

Long press one Push key and Match key at the same time to select 3 kinds light type, and each light type will have different push key function. Long press 1 key and Match key 2 seconds, set as single color type. Long press 2 key and Match key 2 seconds, set as dual color type. Long press 3 key and Match key 2 seconds, set as RGB type. After the light type is set, please repeat network con gure operation by Tuya APP.

RGB dynamic mode list

PWM frequency setting

We can select four PWM frequency: 500Hz, 2KHz, 8KHz or 16KHz. Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).

Dimming curve setting

V3-L(WT) match remote control (Optional)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the V3-L(WT)’s Match key

Match: Short press match key of V3-L(WT), immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. The LED indicator fast flash a few times means match is successful.

Delete: Press and hold match key of V3-L(WT) for 10s, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart
Match: Switch off the power of V3-L(WT), then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful.

Delete: Switch off the power of V3-L(WT), then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

V3-L(WT) work as WiFi-RF converter to match RF LED controller or dimming

driver

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match: Short press match key of the controller, immediately press on/off key on the Tuya APP. The LED indicator fast flash a few times means match is successful.

Delete: Press and hold match key of the controller for 5s, The LED indicator fast flash a few times means match was deleted.

Use Power Restart

Match: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 3 times on the Tuya APP. The light blinks 3 times means match is successful.

Delete: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 5 times on the Tuya APP. The light blinks 5 times means match was deleted.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>