SKYDANCE DS DMX512-SPI Decoder and RF Controller Owner’s Manual

Table of Contents

SKYDANCE-DS-DMX512-SPI-Decoder-and-RF-Controller-Owner's-Manual-
product

Model No.: DS
Compatible with 34 kinds IC/Numeric display/Stand-alone function/Wireless remote control/Din rail

DMX512 to SPI decoder and RF controller with digital display.
Compatible with 34 kinds of digital IC RGB or RGBW LED strips, IC type and R/G/B order can be set.
- Compatible ICs:
- TM1803, TM1804, TM1809, TM1812, UCS1903, UCS1909,
- UCS1912, UCS2903, UCS2909, UCS2912, WS2811, WS2812,
- TM1829, TLS3001, TLS3002, GW6205, MBI6120, TM1814B,
- SK6812, UCS8904B, LPD6803, LPD1101, D705, UCS6909,
- UCS6912, LPD8803, LPD8806, WS2801, WS2803, P9813, SK9822, TM1914A,GS8206,GS8208.
DMX decode mode, stand-alone mode and RF mode are selectable.
Standard DMX512 compliant interface set DMX to decode start address by buttons.
Under stand-alone mode, change mode, speed or brightness by buttons.
Under RF mode, match with RF 2.4G RGB/RGBW remote control.
32 kinds of dynamic modes, including horse race, chase, flow, trail or gradual change style.

Wiring Diagram

Note:

If the SPI LED pixel strip is single-wire control, the DATA and CLK output is the same, we can connect up to 2 LED strips.

IC type, RGB order, and pixel length setting

You must ﬁrst assure the IC type, RGB order and pixel length of the LED strip is correct.
Long press M and ◀ keys, to prepare for setup IC type, RGB order, pixel length, and automatic blank screen, Short press the M key to switch four items.
Press the ◀ or ▶ key to set up the value of each item.
Long press the M key for 2s, or timeout 10s, and quit setting.

IC type table:

RGB order: O-1 – O-6 indicates six orders (RGB, RBG, GRB, GBR, BRG, BGR).
Pixel length: Range is 008-900.
Automatic blank screen: enable (“bon”) or disable(“boF”) automatic blank screen.

DMX decode mode

Short press the M key, when displaying 001-999, and enter DMX decode mode.
Press ◀ or ▶ key to change DMX decode start address(001-999), and long press for fast adjustment.
Long press the M key for 2s, prepare for setup decode number and multiple of pixels. Short press the M key to switch two items.
Press the ◀ or ▶ key to set up the value of each item.
Decode number(display “dno”) : DMX decode channel number, range is 003-600(for RGB).
Multiple of pixels(display “Pno”) : Each 3 DMX channel control length(for RGB), range is 001- pixel length. Long press M key for 2s, or timeout 10s, quit setting.
If there is a DMX signal input, will enter DMX decode mode automatically. For example, the DMX-SPI decoder connects with the RGB strip:
DMX data from DMX512 console:

Short press the M key, when displaying P01-P32, and enter stand-alone mode.
Press the ◀ or ▶ key to change the dynamic mode number(P01-P32).
Each mode can adjust speed and brightness.
Long press the M key for 2s, and prepare for setup mode speed and brightness. Short press the M key to switch two items.
Press the ◀ or ▶ key to set up the value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press the M key for 2s, or timeout 10s, and quit setting.
Enter stand-alone mode only when the DMX signal is disconnected or lost.

Dynamic mode list

RF mode

Match: Long press the M and ▶ keys for 2s, display “RLS”,
within 5s, press the on/off key of the RGB remote, display “RLO”, the match is successful,
then use the RF remote to change mode number, adjust speed or brightness.
Delete Long press M and ▶ keys for 5s, until display “RLE”, delete all matched RF remotes.

Restore the factory default parameter

Long press and key, restore the factory default parameter, and display”RES”.
Factory default parameter: DMX decode mode, DMX decodes start address is 1, decode number is 510, multiple of pixels 1, dynamic mode number is 1, chip type is TM1809, RGB order,
pixel length is 170, disable automatic blank screen, without matched RF remote.