SKYDANCE T18-2 1-10V Rotary Glass Panel Dimmer User Manual
- October 30, 2023
- SKYDANCE
Table of Contents
T18-2 1-10V Rotary Glass Panel Dimmer
User Manual
Rotary dimming/Glass panel/AC relay output/Wireless remote
control
Features
- Rotary glass panel 1-10V dimmer, 1 channel output.
- Output 1 channel 1-10V signal, connect with 1-10V dimmable driver.
- High voltage AC input, High voltage AC relay output.
- Rotate knob to change brightness, support push and long push operation.
- 256 levels 0-100% dimming smoothly without any flash.
- Compatibility with RF 2.4G single zone or multiple zone dimming remote control.
- White & Black glass panel available.
Technical Parameters
Input and Output
Input voltage| AC100-240V
Output signal| 1-10V (50mA)
Output current| Max 1.5A (AC)
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Dimming data
Input signal| Rotary knob + RF 2.4GHz
RF Control distance| 10m(Barrier-free space)
Dimming level| 256 levels
Dimming range| 0 -100%
Environment
Operation temperature| Ta: -30ºC ~ +55ºC
Case temperature (Max.)| Tc: +65ºC
IP rating| IP20
Warranty
Warranty| 5 years
Mechanical Structures and Installations
Typical base as below:
Installation diagram:
Uninstall| Touch panel| Baseplate| Base
Knob function
-
Push: Turn on or off light.
After turn on light: -
Rotate: Rotate knob to adjust brightness, 2.5 turns, 50 levels.
-
Long push(1-6s): Continuous 256 levels brightness adjustment.
Note: The default output is 1-10V, if you want to 0-10V output, please push the knob to turn off light, then push the knob for 15s immediately, the output will become 0-10V. Push the knob to turn off light, then push the knob for 10s immediately, the output will return 1-10V.
Wiring diagram
- Connect with 1-10V dimming driver (no use AC OUT)
- Connect with 1-10V dimming driver (use AC OUT)
- Connect with 1-10V dimming driver (use AC OUT and relay or contactor)
An additional AC relay or contactor is needed when total input current of the load is higher than 1.5A or inrush current is greater than 15A.
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 100 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 50 meters.
Match Remote Control (two match ways)
The 1-10V rotary panel dimmer can also match with the RF dimming remote
(optional).
End user can choose the suitable match/delete ways. Two options are offered
for selection:
Use Knob
Match:
Turn on light, turn off, immediately push the knob for 5s, then press on/off
key (single zone remote) or zone key (multiple zone remote) of the RF remote
within 5s.
The LED indicator fast flash 3 times means match is successful.
Delete:
Turn on light, turn off, immediately push the knob for 10s, The LED indicator
fast flash 6 times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again, Immediately short
press on/off key (single zone remote) or zone key (multiple zone remote) 3
times on the remote. The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again, Immediately short
press on/off key (single zone remote) or zone key (multiple zone remote) 5
times on the remote. The light blinks 5 times means all matched remotes were
deleted.
User Manual Ver 1.1.2
Documents / Resources
|
SKYDANCE T18-2 1-10V Rotary Glass Panel
Dimmer
[pdf] User Manual
T18-2, T18-2 1-10V Rotary Glass Panel Dimmer, 1-10V Rotary Glass Panel Dimmer,
Rotary Glass Panel Dimmer, Glass Panel Dimmer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>