MOUNTUP MU0004 Adjustable Gas Spring Monitor Arm Installation Guide
- June 15, 2024
- MOUNTUP
Table of Contents
INSTALLATION INSTRUCTION
Version 1
MU0004 Adjustable Gas Spring Monitor Arm
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
**** Safety Caution
BEFORE ASSEMBLY
- Please check and make sure all necessary accessories are included and undamaged.
- Please read and understand this manual carefully before installation.
WARNING
- This product contains small items that could be a choking hazard if swallowed. KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
- Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury mounting or caused by improper inappropriate use.
CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Product Dimensions
Parts and Hardware
NOTE: Not all parts and hardware included will be used.
Base Installation
OPTION A: Clamp Installation
Desk Thickness 10~50mm (0.39~1.97″)
A-1
Apply pads (E1&E2) to the base bottom to avoid desk scratches. A-2
Remove the plastic cover from Base (C). Mount Clamp (D) to the bottom of Base
(C) by tightening bolts (K) with 5mm Allen Key (I). A-3
Secure stand to the desktop by tightening clamp (D). Fix the plastic cover to
Base (C). OPTION B:
Grommet Base Installation
Desk Thickness 10~80mm (0.39~3.15″)
B-1
Apply pads (E1&E2) to the base bottom to avoid desk scratches. B-2
If existing grommet hole comes with a plastic protector, remove it to ensure a
flat surface before installing the desk mount.
Detach Bracket (D1) from Clamp (D). B-3
Secure base to the desktop by using Bracket (D1) and Wingnut (F). Install the
plastic cover to Base (C) finally.
Arm Installation
Install the lower arm (B) and the upper arm (A) to the base (C). Secure the
arm by tightening the inside screw using 3mm Allen key (H).
If the inside screws are missing, you can use spare screws.
** DO NOT tighten the screw excessively or it might be stripped.
Note: The side with the label is installed on the base(C). ** Please do not move
stand outside desk for safety!
Monitor Installation
(a) Flat Back|
---|---
(b) Recessed or Curved Back|
Do not tighten the screws excessively or your monitor might be damaged.
- Install the top two screws first with 3-5mm space left..
- And then you attach the monitor to the arm.
- Finally install the next two screws and tighten all four screws.
Adjustments (If necessary)
Tilt Adjustment
- Loosen the tilting bolt.
- Adjust monitor to your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
Tension Adjustament
The gas spring is pre-set for a load-bearing range of 4-6KG. Depending on the
weight of your actual monitor, you may need to adjust the tension of Arm (A)
inaccordance with your monitor weight by 6mm Allen Key (J).
Note: Be sure to keep
the arm in a horizontal position during adjustment. Situation 1: If arm falls
down
Solution: Turn the inside screw counterclockwise to increase
tension. Situation 2:
If arm rises up
Solution: Turn the inside screw clockwise to decrease tension.
Cable Management
Remove the cable cover, run cables through bottom of the arm, then install the
cable cover again.Adjust
monitor position and rotation.
Note: To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it
with both hands, and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help.
INSTALLATION INSTRUCTION
Version 2
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
BEFORE ASSEMBLY
- Please check and make sure all necessary accessories are included and undamaged.
- Please read and understand this manual carefully before installation.
WARNING
- This product contains small items that could be a choking hazard if swallowed. KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
- Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury mounting or caused by improper inappropriate use.
CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Product Dimensions
Parts and
Hardware NOTE: Not all
parts and hardware included will be used.
Base Installation
OPTION A: Clamp Installation
Desk Thickness 10~50mm (0.39~1.97″)
A-1
Apply pads (E1&E2) to the base bottom to avoid desk scratches. A-2
Remove the plastic sleeve and plastic cover from Base (C). Mount Clamp (D) to
the bottom of Base (C) by tightening bolts (K) with 5mm Allen Key (I).
A-3
Secure stand to the desktop by tightening clamp (D). Fix the plastic sleeve
and plastic cover to Base (C).
Base Installation
OPTION B: Grommet Base Installation
Desk Thickness 10~80mm (0.39~3.15″)
B-1
Apply pads (E1&E2) to the base bottom to avoid desk scratches. B-2
If existing grommet hole comes with a plastic protector, remove it to
ensure a flat surface before installing the desk mount.
Detach Bracket (D1) from Clamp (D).
B-3
Secure base to the desktop by using Bracket (D1) and Wingnut (F). Install the
plastic sleeve and plastic cover to Base (C) finally.
Arm Installation
Attach plastic sleeve (L) to the end of upper arm (A). Install the lower arm
(B) and the upper arm (A) to the base (C). Secure the arm by tightening the
inside screw using 3mm Allen key (H).
If the inside screws are missing, you can use spare screws.
** DO NOT tighten the screw excessively or it might be stripped. Note: The side with the
label is installed on the base(C).
Attention: Attach upper arm with plastic sleeve to the lower arm.
** Please do not move stand
outside desk for safety!
Monitor Installation
(a)
Flat Back|
---|---
(b)
Recessed or Curved Back|
Do not tighten the screws excessively or your monitor might be damaged.
- Install the top two screws first with 3-5mm space left..
- And then you attach the monitor to the arm.
- Finally install the next two screws and tighten all four screws.
Adjustments (If
necessary)
Tilt Adjustment
- Loosen the tilting bolt.
- Adjust monitor to your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
Tension Adjustament
The gas spring is pre-set for a load-bearing range of 4-6KG. Depending on the weight of your actual monitor, you may need to adjust the tension of Arm (A) inaccordance with your monitor weight by 6mm Allen Key (J).
Note: Be sure to keep
the arm in a horizontal position during adjustment. Situation 1: If arm falls
down
Solution: Turn the inside screw counterclockwise to increase
tension. Situation 2:
If arm rises up
Solution: Turn the inside screw clockwise to decrease tension.
Cable Management
Remove the cable cover, run cables through bottom of the arm, then install the
cable cover again.Adjust
monitor position and rotation. Note: To
ensure stability, the tightness of the rotating axis has been preset, so it
would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it
with both hands, and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>