n-FAB HPF1777QC Hoop Step Instruction Manual

June 13, 2024
n-FAB

n-FAB HPF1777QC Hoop Step

Product Information

  • I-Sheet Number: INST-00276
  • Part Number: HPF1777QC
  • Product: Hoop Step
  • Application: 17-22 Ford F-250/350 QC

Product Usage Instructions

  1. Locate the driver-side step rail.
  2. Install the (x4) mounting brackets to each attachment point on the main tube using the supplied M10x25 carriage bolts, and M10 hex nuts, and leave them loose for now. Make sure the brackets attach to the backside of the mounting flange with the threaded end of the carriage bolt facing toward the rear of the step.
  3. If equipped, remove all 8mm nuts from the threaded studs and remove the factory running board.
  4. Carefully raise the step into position and align the three brackets with the threaded studs. Ensure that the front of the tube is in front of the plastic guard.
  5. Starting with the rear bracket, push up towards the pinch weld so that the 3 main tube is high and tight to the body of the vehicle. Use the supplied M8 nut, M8 hex bolt, and washers to secure the bottom stud first.
  6. Next, move to the front bracket and push up to level the main tube to the body of the vehicle. Secure all three mounts with the supplied M8 nut and washer. Repeat the same process with the middle bracket and finish tightening the remaining nuts and bolt on the rear brackets.
  7. After the final adjustment, tighten all four brackets at the main tube.
  8. Repeat steps 2-7 for the passenger side.

HARDWARE DESCRIPTION

HARDWARE DESCRIPTION QTY.

 | 8MM NYLOC NUT| 12
 | 8MM ZINC WASHER| 12
 | M10X25mm Carriage bolt| 8
 | M10 hex nut| 8
PARTS INCLUDED| QTY
---|---
DRIVER SIDE STEP| 1
PASSENGER SIDE STEP| 1
Mounting bracket| 4

DO NOT USE IMPACT TOOLS

INSTALLATION STEPS

  • Step 1. Locate the driver side step rail.
  • Step 2. Install the (x4) mounting brackets to each attachment point on the main tube using the supplied M10x25 carriage bolts, M10 hex nuts and leave loose for now.
    • NOTE: The brackets will attach to the backside of the mounting flange with the threaded end of the carriage bolt facing towards the REAR of the step.
  • Step 3. If equipped, remove all 8mm nuts from the threaded studs and remove factory running board.
  • Step 4. Carefully raise the step into position and align the three brackets with the threaded studs.
    • NOTE: Be sure the front of the tube is in front of the plastic guard.
  • Step 5. Starting with the rear bracket, push up towards the pinch weld so the 3” main tube is high and tight to the body of the vehicle, and use the supplied M8 nut, m8 hex bolt, and washers to secure the bottom stud first.
  • Step 6. Next, move to the front bracket and push up to level the main tube to the body of the vehicle and secure all three mounts with the suppled M8 nut and washer. Do the same with the middle bracket and finish tightening the remaining nuts and bolt on the rear brackets.
  • Step 7. After the final adjustment, tighten all four brackets at the main tube.
  • Step 9. Repeat steps 2-7 with the passenger side.

PARTS

  • I-SHEET NUMBER: INST-00276
  • PART NUMBER: HPF1777QC
  • PRODUCT: HOOP STEP
  • APPLICATION: 17-22 FORD F-250/350 QC
  • 12302 Shiloh Church Rd. Houston TX 77066
  • REVISION © 2018 N-FAB, INC.
  • Phone 281-880-6322
  • Fax 281-880-6325
  • REVISION DATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals