n-FAB 15-18 RAM 1500-4500 Hoop Step User Manual

June 13, 2024
n-FAB

n-FAB 15-18 RAM 1500-4500 Hoop Step

n-FAB 15-18 RAM 1500-4500 Hoop Step

HARDWARE DESCRIPTION

HARDWARE DESCRIPTION QTY.

HWKT-00423X
CLIP-00647| 3/8”-16 X 1 ¾” BARREL NUT

CLIP

| 14
FDRW-00736| M8 FENDER WASHER| 12
FLTW-00663X| 3/8” USS FLAT WASHER

ZINCLAD 1000B

| 14
HHCS-00685| 3/8”-16X 1-1/2” HEX CAP

SCREW

| 14
LCKW-00722| M8 SPLIT LOCK WASHER| 12
HHCS-00649| M8-1.25X35MM HEX CAP SCREW| 12
| M10 CARRIAGE BOLT| 12
| M10 FLANGED HEX NUT| 12

PARTS INCLUDED

PARTS INCLUDED QTY
DRIVER SIDE 1
PASSENGER SIDE 1
Mounting bracket 6

INSTALLATION INSTRUCTIONS

Step 1: Identify Driver side step

Installation Instructions

Step 2. Install the (x6) mounting brackets to each attachment point on the main tube and leave loose for now. Note the bracket orientation. The bracket bends towards the front of the vehicle.

Installation Instructions

  • Shorter bracket installs on driver side front

Step 3: Locate the six sets factory mounting hex holes (3 on each side of the vehicle). These are positioned on the vertical sides of the floor pan beneath the doors, with one set of holes each in the front, middle, and rear of the vehicle cab.
Step 4: If you have a 14-18 model you may have to drill a 1” round opening for the rear bracket location to add the second clip. If so, go ahead and complete this step at his time.
Step 5: Using the 3/8″ threaded clips, slide two clips in the upper rectangular hole, and align one clip in each hex hole so the clip threads are visible.

Installation Instructions

NOTE: On 2014 Quad Cab models in the rear mounting location, the hex holes are offset and only the forward mounting hole and clip are used. If desired, the rear clip may be used by cutting a 1″ hole directly above the rear hex hole, and level with the lower edge of the upper rectangular as shown by the dotted diagrams in figure 2.

Step 6: Align the Nerf Step brackets with the three mounting locations on the underside of the vehicle. Start all six 3/8″ x 1″ hex bolts with washers and leave loose.
Step 7: Using a sharpie, outline the upper “U “shaped mount in the center bracket

Installation Instructions

Step 8: Remove Nerf Step and set aside. Next, slide the additional 3/8 threaded clip from the upper rectangle hole and align with the “U” shaped mark from step 5. Make a mark through the threaded part of the clip.

Installation Instructions

Step 9: Remove clip. Use a ½” drill bit and drill out the center mark. Slide the 3/8 clip back into position so the threaded part is aligned with the hole.
Step 10: Repeat Step 5 with the additional upper clip. Starting with the rear Bracket, raise the Nerf step into positon and torque the bolts to 15-20 ft./lbs. Move to the front bracket and torque bolts. Then to the center brackets and torque down bolts.
Step 11: Next, tighten all (x3) brackets at the main tube. (20-25 ft/lbs torque)
Step 12: Repeat Steps 2-11 for passenger side.

Installation Instructions

CUSTOMERS SUPPORT

12302 Shiloh Church Rd. Houston TX 77066 Phone 281-880-6322 – Fax 281-880-6325
REVISION – – © 2018 N-FAB, INC. REVISION DATE 08/01/19

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals