n-FAB HWKT-00848X Hoop Step Installation Guide

June 13, 2024
n-FAB

n-FAB logo HWKT-00848X Hoop Step
Installation Guide

HWKT-00848X Hoop Step

HARDWARE DESCRIPTION QTY.

HWKT-00848X
CLIP-00645X| 3/8″-16 X 9/16″ BARREL NUT| 6
FDRW-00736X| M8 FENDER WASHER| 6
FDRW-03082X| M6 FENDER WASHER| 24
FLTW-00663X| 3/8″ USS FLAT WASHER| 6
H HCS -00649X| M8-1.25 X 35MM CLASS 8.8 HEXCAP SCREW| 6
H HCS-00685X| 3/8″-16 X 1-1/2″ GRADE 5 HEX CA[ SCREW| 6
H HCS-03080X| M6-1.00 X XXMM CLASS 8.8 HEX CAP SCREW| 12
HXNT-03083X| M6-1.00 CLASS B FINISHED HEX NUT| 12
| M10 CARRIAGE BOLT| 12
| M10 FLANGED HEX NUT| 12

PARTS INCLUDED QTY
DRIVER SIDE 1
PASSENGER SIDE 1
MOUNTING BRACKETS 6

Step 1: Locate the driver side step rail.

n-FAB HWKT-00848X Hoop Step - driver side step rail

Step 2. Install the (x6) mounting brackets to each attachment point on the main tube and leave loose for now.
NOTE: Mount the bracket on the back side of the welded tab so the threaded part of the fastener points towards the rear of the vehicle.

n-FAB HWKT-00848X Hoop Step - Bracket bends

Step 3: Depending on your cab model, you will have to identify which hardware you will have to use for the upper (3) mounts on the underside of the body. There will either be existing 8mm threaded holes for the M8 x 20mm hex head bolts or open slots for the 3/8” speed clips and 3/8”x 1 ¼” Hex bolts.

n-FAB HWKT-00848X Hoop Step - Threaded hole Step.4 Carefully raise step rail up to the pinch weld of the body and align brackets up with the factory mounting locations.
Step. 5 Depending on your hardware selection made in step 2, fasten the upper mounts and leave loose at this time.n-FAB HWKT-00848X Hoop Step -
hardware selection Step. 6 Next, start all (x6) ¼-20”x 3/4” hex bolts, (x12) M8 flat washers, (x6) 5/16” lock washers and (6) ¼”-20 HC Nut in the pinch weld mounting locations and leave loose for now.n-FAB HWKT-00848X Hoop Step - mounting locations

Step. 7: After finial positioning, completely tighten all (x6) ¼”-20 x ¾” in the pinch weld attachment.
Step. 8: Next, tighten all (x3) upper body mount positions to 17-20 Ft/lbs. torque.
Step 9: Finish by tightening all three brackets at the main tube.
Step 10: Re-peat steps 3-9 with passenger side.n-FAB HWKT-00848X Hoop
Step - passenger side

12302 Shiloh Church Rd. Houston TX 77066
REVISION – –
© 2018 N-FAB, INC.
Phone 281-880-6322
Fax 281-880-6325
EVISION DATE 08/01/19

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals