BRExhaust 106-0062 Direct Fit Replacement Exhaust System Instruction Manual
- June 13, 2024
- BRExhaust
Table of Contents
BRExhaust 106-0062 Direct Fit Replacement Exhaust System
Product Information
The product is an exhaust system for vehicles. It is designed to replace the original equipment manufacturer (OEM) exhaust system. The exhaust system is manufactured by BRExhaust and is accompanied by installation instructions.
The product includes the following items:
- Item 1 – Specific component (not mentioned in the text)
- Item 2 – Specific component (not mentioned in the text)
- Item 3 – Specific component (not mentioned in the text)
- Item 4 – Specific component (not mentioned in the text)
The product is designed to improve the vehicle’s exhaust performance and may require professional installation.
Product Usage Instructions
- Carefully read all instructions before starting the installation process.
- Disconnect the vehicle’s battery before removing the OEM exhaust system to prevent electrical accidents and reset the computer if applicable.
- Remove the existing exhaust system from the vehicle, but only remove parts that will be replaced.
- Clean the existing flange using a wire brush to ensure proper sealing.
- Begin installation by attaching items 1 and 2 to the existing exhaust.
- Attach item 4 to the isolators.
- Attach item 4 and item 2 together using item 3.
- Attach the clamp provided with item 2 on the slip fit joint.
- Ensure that the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
- Tighten all clamps and bolts starting from the rear of the vehicle. Do not exceed 30 ft-lb when tightening the clamp. Check all clamps after driving 50 miles and retighten if necessary.
Warning:
- When working on, under, or around any vehicle, exercise caution.
- Allow the vehicle’s exhaust system to cool before removal to prevent severe burns from exhaust temperatures.
- If working without a lift, always consult the vehicle manual for correct lifting specifications.
- Always wear safety glasses and ensure a safe work area.
- Failure to follow safety measures could result in serious injury or death.
For technical support, contact BRExhaust at 1-800-631-7271. The company is located at 1901 Corporate Ctr, Oceanside, CA 92056. You can also visit their website at www.brexhaust.com.
INSTALLATION INSTRUCTIONS
-
STEP 1:
(Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing. -
STEP 2:
Begin installation by installing items 1 and 2 to existing exhaust -
STEP 3:
Attach item 4 to isolators -
STEP 4:
Attach item 4 and item 2 together with item 3 -
STEP 5:
Attach clamp provided with item 2 on the slip fit joint -
STEP 6:
Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain. -
STEP 7:
Tighten all clamps and bolts starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
WARNING:
When working on, under, or around any vehicle exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
BRExhaust recommends professional installation for all products
Technical Support: 1-800-631-7271
BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>