WELOCK PCB10KEY28 Smart Door Lock Cylinder Instructions

PCB10KEY28 Smart Door Lock Cylinder
Instructions

PART LIST FIGURE

1. Screws for battery compartment
2. Front Handle
3. Front Panel
4. Screw casing
5. Profile cylinder
6. Scerws for profile cylinder
7. Toggle lever
8. Rear Panel
9. Scerws for rear Panel
10. Rear handle
11. Mounting bracket
12. Mounting bracket screw
13. Mbase
14. Product ID

Accessory list(TOOL BOX)

|
---|---
Euro Profile Cylinder1| Mounting bracket1
|
Sticker2 (Used to cover the door hole]| Mbase1
|
KIY2| Fixing screw15
|
Phillips screwdriver & Thimble| RFID Cord3
|
Battery installation assistance tool1| Product ID1
Manual1

Install battery

1. Insert the battery installation assistance tool and rotate to open the battery comportment cover

2. Install batteries

3. Open the silicone cover

4. Tighten the screws

Operating instruction

1. If enter wrong passcode 5 times continuously. the system will be locked for three minutes and cannot operate.

2. Press to woke up the keyboard+ IO digits temporary posscode.Enter wrong passcode 5 times continuously,the system will be locked for three minutes and con not operate.
   Temporary passcode generation needs to be done in the App. The time on the screen should be some as the time on the phone.otherwise the tempororyposscode will be invalid.

3. Press to woke up the keyboord+swipe the RFID cords.
   Swipe the unmatched cord Slimes continuously. the system is locked for three minutes and cannot operate. Any RFID cord con unlock the door in factory state.

4. Bind the lock on APP
   Bind the lock on APP via Bluetooth,click”unlock”,then the phone time will be synchronized to the lock via Bluetooth.

Unlock and lock

Unlock the door from outside.You con unlock the door from any direction.To protect the door from damage by forceful torsion. the front handle will keep free rotating until the lock is unlocked by correct way.
The rear handle can be turned left or right 90º
To protect the lock not be damaged by torsion forcefully Resetting diagram

1. Open the silicone cover

2.  Find the Thimble in the attached accessories

3. Find the hole where the reset button is located

4. Insert the thimble into the hole and press the reset button

Installation diagram

2.1 Picture of installation Inward opening door:
The inclined surface of the bolt face outwards when installing.

1. The length of the cylinder con be adjusted according to the diameter of the keyhole

2. Instoll the lock body and tighten the screws
   

3. Place the lock body and tighten the screws

4. Instoll outdoor

5. Install the mounting bracket ond tighten the mounting bracket screws

6. Install the rear panel handle ond tighten the screws

7. Passcode:Flow chart
   

8. RFID card: Flow chart
   

9. Other settings: Flow chart
   

Scan the QR code on the lock Downloadable Instructions & Watch Videos
A smart way to open your door.WE.LOCK
www.WELOCK.COM

Applicable size

Product Introduction

Bluetooth activation and login instructions Select “Android/iOS” to download Log in to the app

1. Select your country/region
2. Enter the phone number/email to get the verification code
3. Click”Send”
4. Enter the verification code after receiving the message
5. Click”Login”

Bind the device

Specifications

FAQ

• When should you replace the battery?****

– When the low battery alarm occurs,the battery needs to be replaced in time.

• When will there be low battery alarm?****

– When the battery power is less than 20%.

• How can you enter scramble code?****

– Enter any number before and after a correct passcode,30 digits or less.

• How can you unlock the lock when the battery runs out?****

– You can use a mobile power supply to power the lock via a micro USB cable,and then use our App to unlock.

• How can I contact customer service?****

– Please contact this email: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>