BRExhaust 106-0513 Kits Exhaust Pipe Instruction Manual

BRExhaust 106-0513 Kits Exhaust Pipe

Product Information

The product is an exhaust system manufactured by BRExhaust.

• Part Number : 106-0513

Bill of Materials

• 1 x 167540
• 1 x 168725
• 1 x 167702
• 1 x 168665
• 1 x 168596
• 1 x 168724
• 1 x 168723

Product Usage Instructions

STEP 1
Carefully read all instructions before installation. Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove the existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean the existing flange with a wire brush to ensure proper sealing.

STEP 2
Attach item 2/6/7 (match length to OE system) to existing isolators and exhaust with item 1 (nuts and bolts not included).

STEP 3
Attach item 4 to item 2/6/7 with item 3.

STEP 4
Attach item 5 to existing isolators and item 3 with item 4.

STEP 5
Connect slip fit for items 6 with clamps provided.

STEP 6
Ensure the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.

STEP 7

• Tighten all clamps starting from the rear of the vehicle.
• Do not exceed 30 ft-lb when tightening clamp and check all clamps after 50 miles. Retighten if necessary.

WARNING
When working on, under, or around any vehicle, exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult the vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.

BRExhaust recommends professional installation for all products.

• Technical Support: 1-800-631-7271
• BRExhaust: 1901 Corporate Ctr, Oceanside, CA 92056

www.brexhaust.com

INSTALLATION INSTRUCTIONS | PART NO. 106-0513

BILL OF MATERIALS

1. 167540
2. 168725
3. 167702
4. 168665
5. 168596
6. 168724
7. 168723

STEP 1
(Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing.

STEP 2
Attach item 2/6/7 (match length to OE system) to existing isolators and exhaust with item 1 (nuts and bolts not included)

STEP 3
Attach item 4 to item 2/6/7 with item 3

STEP 4
Attach item 5 to existing isolators and item 3 with item 4

STEP 5
Connect slip fit for items 6 with clamps provided

STEP 6
Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.

STEP 7
Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)

WARNING
When working on, under, or around any vehicle exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.

BRExhaust recommends professional installation for all products

• Technical Support : 1-800-631-7271
• BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056
• www.brexhaust.com

References

• MagnaFlow Exhaust, Mufflers & Cat Converters - Quality. Power. Sound.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>