LOG BARN 38956 Light Industrial Chandeliers User Manual
- June 16, 2024
- LOG BARN
Table of Contents
38956 Light Industrial Chandeliers
User Manual
38956 Light Industrial Chandeliers
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as
below picture 
PARTS TYPE & QTY INCLUDING:
(A) Hex nut (1)
(C) Nipple (1)
(E) Single bar (1)
(F) Green ground screw (1)
(G) Canopy (1)
(H) Collar ring (1)
(I) Collar loop (1)
(J) Quick link (2)
(K) Chain (1)
(L) Tube (1)
(M)Fixture body (1)
(N) Socket(3)
(O) Arm (3)
ACCESSORIES & QTY ENCLOSED:
(B) Mounting screw (2)
(D)Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and
accessories are included as shown in the above illustration
2. Make assembly
If the group of parts are not already assembled:
Step A1: Thread the single bar(E) over the nipple (C) a
minimum of 6 mm (1/4”). At this point need note that: the side of single bar
marked “GND” must face to the down.
Step A2: Thread the hex nut (A)onto the nipple (C) till snug.
Step A3: Thread the collar loop (I) onto the nipple (C).
3. Make pre-installation
Step B1: Thread the tube (L)onto the
fixture body (M) till tight .
Step B2: By measuring, determine the correct number of links needed for
proper hanging height. Using the chain pliers, disconnect and discard the
remaining chain.
Step B3: Open the quick link (J) to connect the loop of tube (L) and the
chain (K), Close the quick link (J).
Step B4: Carefully lace the wires through the chain (K)(every other
link)and stop just before you reach the top of chain (K).
Gently pull the wires till snug.
4. Turn off power
Before you start to make installation, NEVER attempt any work without shutting
off the electricity until the work is done.
A). Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “OFF” position. B). Place the wall switch in the“OFF”
position
5. Make installation
Step C1: Attach the single bar (E) to
outlet box with mounting screws (B). The side of single bar marked “GND” must
face out Unscrew the collar ring (H) from the collar loop
Step C2: Raise the canopy (G) through the collar loop (I) and screw the
collar loop (I) to a proper position by measuring.
Unscrew collar ring (H) from the collar loop (I) and remove the canopy (G). In
this way, you would know the Proper position on which collar loop it should be
located.
Note: The canopy (G) should be snug against the ceiling and the collar
loop (I) should be screwed enough threads (no less than 6 threads )over the
threaded nipple (C) for more secure hanging .If not, adjust the collar loop
(I) on the single bar assembly (E) by screwing the collar loop (I) in or out
of the single bar (E) until the length is achieved.
Step C3: Slip the collar ring(H) over the chain(K),then do the same with
the canopy(G)
Step C4: Open the quick link(J)，attach the quick link (J) to connect the
screw collar loop (I). Close the quick link(J) Pass the wires through the
collar loop(H) to the top of nipple(E) and gently pull till snug.
Step C5: If needed, cut off the wires length of fixture.At this point,
the remaining wire length measured from the top of single bar(B) should be at
least 6″.
Step C6: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF
FIXTURE ,NEVER CONNECT WIRES TO GROUND WIRES
Connect ground wire according to below chart
Connect wires according to below chart
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| Black | White |
| *Parallel cord ( round & smooth ) | *Parallel cord ( square & ridged ) |
| Clear,Brown,Gold or Black without tracer | Clear,Brown,Gold or Black with |
tracer
Insulated wire ( other than green) with copper conductor| Insulated wire (
other than green) with silver conductor
*Note: When paraliel wires (SPT I & SPT II) are used. The neutral wire is
square shaped or ridged and the other wire will be round in shape or smooth
(see illus. )
Twist plastic wire connector(D) until wires
are tightly joined together,wrap each connector with approved electrical tape
for more secure connection, then carefully stuff all wires into the outlet box
Step C7: Raise canopy (G) to ceiling and secure canopy (G) in place by
tightening collar ring (H) onto collar loop (I)
Step C8: Install bulbs (not included) (Please do not exceed the maximum
capacity recommended on the socket.)
6. Check everything is already installed properly, then you could turn on
the light. Enjoy!
CLEANING
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>