EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual

June 6, 2024
EcoDim

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User
Manual

Please Read this manual Carefully before installation. Important!

  • It is dangerous if people without proper training work on an electrical installation!
  • There may be a dangerous voltage at the output of the dimmer!
  • When working on the wiring always switch off the mains voltage. Failure to observe this warning may result in death or serious injury!
  • Read the instructions carefully. Incorrect installation may damage the dimmer beyond repair.

Smart Dimmer Module 250W LED Item NO. Eco-Dim.10 Zigbee

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual - product
Overview

  • Zigbee support
  • Suitable for several home automation apps
  • Voice support (Amazon Alexa & Google Assistant / Homey)
  • Works with push-button (momentary switch)
  • Optimal dimmable & light stability
  • Suitable for 250W LED Saves and restores the last status after a power failure
  • MIN and MAX light adjustment and dimming speed Suitable for 90% of all LEDs
  • Does not require a neutral wire, 3 wired connection available
  • Soft start system
  • Noiseless dimming

1. Specifications

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual -
Specifications

2. Installation

1). Turn off the power
To prevent electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation and maintenance. Be aware that even if the circuit breaker is off, some voltage may remain in the wires — before proceeding with the installation, be sure no voltage is present in the wiring. Take extra precautions to avoid accidentally turning the device on during installation.

2). Connect the device exactly according to the diagrams shown below
The dimmer is available for 2 and 3 wired connection. Please note in case of a 2 wired connection port 3 and Load must be connected to make stable dimming possible.

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual - Connect the
device exactly according to the diagrams

3). Turn the power back

3. Min./Max./Dimming Speed adjustment

For the SMART dimmer to work optimally or suitable for your preference, you can adjust the brightness at the Min. and Max. level and also the dimming speed with the MIN./MAX./Dimming Speed adjustment.

  • MIN adjustment: Switch on the lights, insert a screwdriver in MIN and turn to the left. When the light becomes unsteady, turn slightly back to the right so that the light remains steady.
  • MAX adjustment: Switch on the lights, insert a screwdriver in MAX and turn to the right. When the light becomes unsteady, turn slightly back to the left so that the light remains steady.
  • Dimming Speed adjustment: Insert a screwdriver in Speed, clockwise to increase the dimming speed when you push the momentary switch, vice versa.

4. Zigbee Setting

1). Factory Reset

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual - Factory
Reset

Please Note: This procedure should only be used when the primary controller is inoperable. All configuration will be reset after the device is reset or removed from the network.

2). Inclusion to a Zigbee Network
Step 1. Remove the device from the previous Zigbee network in case it has been added to, otherwise pairing mode will fail.

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual - Inclusion to a
Zigbee Network

3). Remove from a Zigbee Network
Method 1. Choose delete or reset as instructed from your Z-Wave hub interface
Method 2. Remove from the Device, see below instructions.

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual - Remove from a
Zigbee Network

4) Touch Link

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual -
TouchLink Note:
a. When both devices (dimmer and remote) are not included in a Zigbee Network, each dimmer can link with max. one remote.
b. When both devices are included in the same Zigbee network, each dimmer can link with max 30 remotes.
c. For Philips Hue Hubs and Amazon Echo Plus, add remote and device to network first then touchline.

5) Find and Bind
Note: Make sure the device and remote already added to the same Zigbee network

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual - Find and
Bind

EcoDim Eco-Dim.10 Zigbee 250W Smart LED Dimmer User Manual -
Address

www.ecodim.nl

 Info@ecodim.nl 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals