Drone Warehouse K101 Max Flight Time Dual Camera User Manual

Drone Warehouse K101 Max Flight Time Dual Camera

Please read this manual carefully before operation and keep it properly for future reference.

Obstacle Avoidance Mode

• Press the button to turn on the obstacle avoidance mode, and press again to turn off the obstacle avoidance mode. Avoid obstacles on three sides and retreat in the opposite direction of the obstacle.
• It is recommended to turn on the obstacle avoidance function in an indoor flight environment with a length and width of 6x 6 meters or more. When the UAV turns on the obstacle avoidance mode, the speed will slow down and the fast gear cannot be turned on.
• Therefore, it is recommended to fly indoors when the obstacle avoidance mode is turned on.

KNOW YOUR REMOTE CONTROL

KNOW YOUR DRONE
With a 2.4G frequency band for long remote control distance, Drone allows multiple flights at the same time without any interference. Users can control it to fly, hover and take photos/ videos with an APP and WIFI connection on a smart phone.

1. Upper Casing
2. Lower Casing
3. Propeller
4. Arm
5. Battery
6. m
7. cotor camera

ACCESSORIES

Notes
Please check the number of accessories carefully (as shown above).Please provide proof of purchase and contact the store for replacement if any missing parts.

OPTIONAL ACCESSORIES LIST

Notes

• If any of the above accessories are damaged during operation, you can contact the seller to purchase them.

FLIGHT ENVIRONMENT

• Indoor: Spacious spaces away from barriers, crowds or pets are preferred.
• Outdoor: Sunny, windless and breezy weathers are preferred.
• Please keep the drone in sight during the flight and keep it away from barriers, high-tension cables, trees and people.
• Do not fly in extreme environments, such as hotness, coldness, strong wind or heavy rain.

OPEN THE WINGS

OPENING STEPS

1. Open the front arm(close to the camera)
2. Open the back arm Fold the back arms first and then the right arm when folding.

ASSEMBLING PROTECTIVE GUARD

Align the protective frame with the arm and install it (Figure 1), press it until it is in place, and then press the position (Figure 2) up to fasten the protective frame.

ASSEMBLING PROPELLERS

Align the blades with the motor shaft and install them (the arm identification must be consistent with the blade identification), Tighten the screw clockwise.

BATTERY CHARGING FOR DRONE

• A. Remove the lithium battery from the bottom of the drone.
• B. Connect the USB charging cable with the charging interface of the lithium battery.

Notes

• LED lights are on when charging and the red light turn off when full charging completes. The charging time is about 150 minutes.

BATTERY INSTRUCTIONS

• There is a certain risk when using lithium batteries. It may cause fire, body injury, or property loss. Users must be aware of the risks and take full responsibility for using batteries improperly.
• If battery leakage occurs, please avoid contacting your eyes or skin with electrolytes. Once it happens, please wash your eyes with clean water and seek medical care immediately.
• Please remove the plug immediately if you sense any peculiar smell, noise or smog.

Battery Charging

• Please use the charger from original factory to ensure your safe usage.
• Do not charge dilatant or outworn battery.
• Do not over charge battery. Please unplug the charger once fully charged.
• Do not charge the battery next to inflammables, such as carpet, timber floor, or wood furniture, or on the surface of electro-conductive objects.
• Please always keep an eye on the battery when charging.
• Do not charge a battery which not cool down yet. The charging temperature should be between 0Cto 40°C.

Battery Recycling

• Do not dispose of the battery as daily rubbish. Please familiarize yourself with the local garbage disposal method and dispose according to the special requirement.

LITHIUM BATTERY INSTRUCTION

1. Open the remote control battery cover
2. Remote control battery installation

Open the battery cover and insert the 3 AAA batteries correctly according to the electrode instructions. (Batteries not included)
Notes

1. Make sure the battery is loaded correctly according to the polarity indications on the battery compartment.
2.  Please do not mix old and new batteries together.
3. Please do not mix different types of batteries together.

SIGNAL CONNECTION OF TRANSMITTER AND RECEIVER

1. Turn on the drone and place it on a level surface, the indicator light of transmitter and the LED of drone flashing.
2. Push the throttle joystick to the highest point then push back to the lowest point, and whenyou hear two beeps, the indicator light of transmitter and the LED of drone become normally on, the signal connection as completed.

TRANSMITTER CALIBRATION

If the drone cannot rise vertically after taking off, you can calibrate the drone, press the button to correct (or move the left and right control sticks to the lower left and lower right respectively), and hear a “beep”, then the indicator light on the drone Blinking quickly, wait for the indicator light to be on, the calibration is complete. When executing the calibration command. it must be executed in a stable state parallel to the horizontal line, otherwise the calibration effect will be affected. Long press the button to make the drone stop in an emergency.

START YOUR FLIGHT

1. One-key Ascend and One-key Landing Press the “One-key Ascend” button, the drone blades rotate and automatically fly to a height of 1.5 meters. Press the button again to land the drone with one button
2. Basic Flight
   Use the left joystick to control the flight altitude and turn left/ right, and the right joystick to control the forward, backward, left and right side flight directions.

Left joystick

Right joystick

Flips & Rolls
When the drone is reaching more than 3 metershigh, click 360° flips and rolls” and move theright joystick to a certain direction, the drone will rotate in that direction.
Right joystick

Hover
When you release the left joystick (throttle) after the ascent/ descent action, the dronewill hover at a certain height.

Left joystick

High/low speed and Light control
Lightly press the button to control the speed of the drone, a “di” sound is a slow speed, and then tap the button again, a “di” and a “di” sound twice as a fast speed, and then the cycle repeats. The default speed of the drone is low speed.
Long press the button to turn on the aircraft lights, and then long press the button to turn off the aircraft lights.

Headless Mode and One key to return home

1. * The flight direction of a drone is subjected to the direction of the remote control.

2. When the drone adjusts the frequency, the drone has defaulted to a common mode. Then the indicator light of the drone is normally on. Short press the headless function key of the remote control, the remote control beeps once and enters a headless state. When you press the headless function key again, you listen to a long beep sound and the drone exits the headless mode.
3. In the headless state, the operator doesn’t need to identify the direction of the nose but control the drone according to the operating lever of the remote control.
   • Long press the button for the drone to return home, and the drone will automatically return in the same direction as it took off,

FINE-TUNING FUNCTION

• When the aircraft spins in the air or tilts in different directions, you can use fine-tuning to correct the action.
• Press the fine-tuning button and hear a beep, then move the joystick in the opposite direction to adjust and calibrate until the aircraft does not deviate.
• If there is no operation for 5-6 seconds after entering the fine-tuning, the fine-tuning function will automatically exit.

Notes

• When the drone is within 30cm from the ground, it will be affected by the blade vortex made by itself and become unstable. This is “ground effect”. The lower the drone is, the greater the effect will be.

FAQ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>