BRExhaust 106-0114 Direct Fit Replacement Exhaust System Instruction Manual
- June 13, 2024
- BRExhaust
Table of Contents
BRExhaust 106-0114 Direct Fit Replacement Exhaust System
Product Information
The product is an exhaust system for a vehicle, manufactured by BRExhaust. It is designed to replace the OEM (Original Equipment Manufacturer) exhaust system. The exhaust system consists of several components, numbered as follows:
- Item 1: Unspecified component
- Item 2: Isolators
- Item 3: Component to be attached to item 2 and existing exhaust
- Item 4: Component to be placed between item 2 and item 3
The installation instructions provide step-by-step guidance on how to install the exhaust system properly. It is important to follow these instructions to ensure correct installation and prevent any accidents or damage.
Product Usage Instructions
- Carefully read all instructions before installation.
- Disconnect the vehicle’s battery before removing the OEM exhaust system to prevent electrical accidents and reset the vehicle’s computer if applicable.
- Remove the existing exhaust system from the vehicle, but only remove the parts that will be replaced.
- Clean the existing flange with a wire brush to ensure proper sealing.
- Attach item 2 (isolators) to the designated location.
- Attach item 3 to item 2 and the existing exhaust.
- Place item 4 between item 2 and item 3.
- Place item 1 between item 3 and the existing exhaust.
- Ensure that the new exhaust system is not contacting any portion of the underbody of the vehicle or drivetrain.
- Tighten all clamps starting from the rear of the vehicle. Do not exceed 30 ft-lb when tightening the clamp. After driving 50miles, check all clamps and retighten if necessary.
It is important to exercise caution when working on, under, or around any vehicle. Allow the vehicle’s exhaust system to cool before removal to avoid burns from high exhaust temperatures. If working without a lift, consult the vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area to prevent serious injury or death. BRExhaust recommends professional installation for all its products. If you require technical support, you can contact them at 1-800-631-7271. Their address is BRExhaust, 1901 Corporate Ctr, Oceanside, CA 92056. For more information, you can visit their website at www.brexhaust.com.
INSTALLATION INSTRUCTIONS
PART NO. 106-0114
-
STEP 1:
(Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing. -
STEP 2:
Attach item 2 to isolators -
STEP 3:
Attach item 3 to item 2 and existing exhaust -
STEP 4:
Place item 4 between item 2 and item 3 -
STEP 5:
Place item 1 between items 3 and existing exhaust -
STEP 6:
Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain. -
STEP 7:
Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
WARNING:
When working on, under, or around any vehicle exercise caution. Please allow
the vehicle’s exhaust system to cool before removal, as exhaust temperatures
may cause severe burns. If working without a lift, always consult vehicle
manual for correct lifting specifications. Always wear safety glasses and
ensure a safe work area. Serious injury or death could occur if safety
measures are not followed.
BRExhaust recommends professional installation for all products
Technical Support: 1-800-631-7271
BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056
www.brexhaust.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>