bouncepad BP-COR-S6-W Core Swivel 60 Instruction Manual
- September 12, 2024
- bouncepad
Table of Contents
bouncepad BP-COR-S6-W Core Swivel 60
INSTRUCTION MANUAL
Tools Required:
- Pencil
- Electric Drill
- 7mm Spanner *or adjustable spanner
- 5.0mm Drillbit *if fixing from below
- 2.5mm Drillbit *if fixing from above
- 16mm Holesaw
*if routing the tablet cable through your mounting surface - Socket Driver
Sheet Code: BP-IM-090_REV0
Release Date: 15/08/2024
Copyright 2024 Spotspot Ltd. (T/A Bouncepad) all rights reserved.
Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder.
In the Box
Fixings List
- Due to the modular nature of our product range you may receive additional fixings in the fixings kit
Tools Required:
- Pencil
- Electric Drill
- 7mm Spanner *or adjustable spanner
- 5.0mm Drillbit *if fixing from below
- 2.5mm Drillbit *if fixing from above
- 16mm Holesaw
- Socket Driver
In the Box:
- Flat Cable
- Fixings Kit
- Tablet Mount Plate
- Shell
- Static60 Mounting Arm
Step-by-Step Assembly:
Step A – Fixing from Above:
- Configure the rotation range – arrows must point in the same direction.
- Attach the Static60 Arm leaning forward in the same direction as the arrows.
- Use the hole template to mark hole positions on the mounting surface.
- Drill the required holes.
- Secure the Rotate to the mounting surface.
- Screw in the Socket Set Screws and secure to the surface.
- Attach the Shell to the Static60 in the correct orientation.
Step B – Fixing from Below:
- Configure the rotation range – arrows must point in the same direction.
- Attach the Static60 Arm leaning forward in the same direction as the arrows.
- Use the hole template to mark hole positions on the mounting surface.
- Drill the required holes.
- Screw in the Socket Set Screws and secure to the surface.
- Attach the Shell to the Static60 in the correct orientation.
Note:
*Before attaching the Mounting Plate, fully clean the back of the tablet with the provided wipe and allow it to dry.
A. Follow steps A if “Fixing from above”.
B. Follow steps B if “Fixing from below”.
1. Configure the rotation range – both arrows must point in the same direction. Default configuration is 270˚. Insert 2x limit screws.
2. Attach the Static60 Arm. The Static60 Arm must lean forward in the same direction as the two arrows.
3. Using the hole template (see step A or B), mark the hole positions specific to your chosen fixing method.
A1. Mark ‘A’ positions for “Fixing from above” (Ø2.5mm drillbit). Mark ‘C’ for the cable hole. (Ø20.0mm Holesaw).
B1. Mark ‘B’ positions for “Fixing from below” (Ø5.0mm drillbit). Mark ‘C’ for routing the cable hole. (Ø20.0mm Holesaw).
4. Drill the required holes.
A2. Lift & hold the rubber screw covers.
A3. Secure the Rotate to the mounting surface, then close the covers.
A4. Go to step 5
B2. Screw in the 4x Socket Set Screws. Ensure full thread engagment.
B3. Secure to the surface. Locking nuts offer greater security.
B4. Go to step 5.
5. Locate & attach the Shell to the Static60 in the correct orientation.
6. Remove the Mounting Plate adhesive backing. Attach level & centrally to the Tablet back as shown.
8. Attach the Flat Cable to the Tablet with the U-Bend Head.
8. Secure the Flat Cable to the Mounting Plate with the Cable Clamp as shown.
9. Remove the Fixing Covers. Feed the Flat Cable into the assembly & locate the Tablet in the chosen orientation.
10. Secure the Tablet to the Shell & attach the Fixing Covers as shown.
11. Connect tablet to power & installation is now complete.
Specifications:
-
Product Name: Core Swivel 60
-
Sheet Code: BP-IM-090_REV0
-
Release Date: 15/08/2024
-
Manufacturer: Spotspot Ltd. (T/A Bouncepad)
-
-
FAQ:
Q: Can I use electric tools for assembly?
A: It is recommended to tighten screws using hand tools to avoid damaging your Bouncepad.
Q: What is the maximum mounting surface thickness?
A: The maximum thickness is 25mm (1 inch).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>