BRExhaust 106-0098 OE Replacement Exhaust System Instruction Manual
- June 13, 2024
- BRExhaust
Table of Contents
BRExhaust 106-0098 OE Replacement Exhaust System
Product Information
- The product is an exhaust system, identified by the part number 106-0098. It is manufactured by BRExhaust, a company located at 1901 Corporate Ctr, Oceanside, CA 92056.
- The exhaust system is designed to replace the OEM (original equipment manufacturer) exhaust system in a vehicle. It consists of multiple components, including item 1, item 2, item 3, item 4, item 5, and item 6.
- Professional installation is recommended for all products by BRExhaust.
- For technical support, you can contact BRExhaust at 1-800-631-7271. More information can also be found on their website at www.brexhaust.com.
Product Usage Instructions
- Carefully read all instructions before installation.
- Disconnect the vehicle’s battery before removing the OEM exhaust system to prevent electrical accidents and reset the computer if applicable.
- Remove the existing exhaust system from the vehicle, only removing the parts that will be replaced.
- Clean the existing flange with a wire brush to ensure proper sealing.
- Attach item 2 to the existing exhaust using item 1.
- Connect item 4 to the existing isolators and item 2 using item 3.
- Connect item 6 to the existing isolators and item 4 using item 5.
- Connect the slip-fit joint on item 4 with the provided clamp.
- Ensure that the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
- Tighten all clamps starting from the rear of the vehicle. Do not exceed 30 ft-lb when tightening the clamps. Check all clamps again after driving 50 miles and retighten if necessary.
- It is important to exercise caution when working on, under, or around any vehicle.
- Allow the vehicle’s exhaust system to cool before removal to prevent burns from exhaust temperatures.
- If working without a lift, always consult the vehicle manual for correct lifting specifications.
- Always wear safety glasses and ensure a safe work area to prevent serious injury or death.
INSTALLATION INSTRUCTIONS
WARNING
- When working on, under, or around any vehicle exercise caution.
- Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns.
- If working without a lift, always consult the vehicle manual for correct lifting specifications.
- Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
- STEP 1: (Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system.
- This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove the existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing.
- STEP 2: Attach item 2 to the existing exhaust with item 1
- STEP 3: Connect item 4 to existing isolators and item 2 with item 3
- STEP 4: Connect item 6 to existing isolators and item 4 with item 5
- STEP 5: Connect slip fit joint on item 4 with clamp provided
- STEP 6: Ensure the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
- STEP 7: Tighten all clamps starting from the rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING THE CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
- BRExhaust recommends professional installation for all products
Technical Support: 1-800-631-7271
Documents / Resources
|
BRExhaust 106-0098 OE Replacement Exhaust
System
[pdf] Instruction Manual
106-0098 OE Replacement Exhaust System, 106-0098, OE Replacement Exhaust
System, Replacement Exhaust System, Exhaust System
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>