BRExhaust 106-0751 Direct Fit Replacement Exhaust System Instruction Manual

June 13, 2024
BRExhaust

BRExhaust logo 106-0751 Direct Fit Replacement Exhaust System
Instruction Manual

106-0751 Direct Fit Replacement Exhaust System

BRExhaust 106-0751 Direct Fit Replacement Exhaust
System INSTALLATION INSTRUCTIONS | PART NO. 106-0751

WARNING:
When working on, under, or around any vehicle exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult vehicle manual  for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
STEP 1: (Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove  existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing.
STEP 2: For 2014 and up you may need to cut the piping of your OE exhaust system before installation. Refer to Table 1 on Page 2 of this document. Measurements are to be made rearward of the DPF beginning from the DPF rear weld  junction. Refer to Table 2 on Page 2 of this document for clamp and year range usage.
STEP 3: For 2007.5-2013 attach [2] Inlet Pipe Assembly to existing exhaust with supplied [1] Hardware and Gasket. For 2014 and up installation attach [4] Extension Pipe to existing exhaust with supplied [3] Clamp.
STEP 4: For 2007.5-2013 attach [4] Extension Pipe to [2] Inlet Pipe Assembly with supplied [3] Clamp.
STEP 5: Attach [8] Over Axle Pipe Assembly to [4] Extension Pipe and appropriate 2007-2019 long [6] Hanger Clamp or 2020 and up short [7] Hanger Clamp to existing isolators with supplied [5] Clamp.
STEP 6: Attach [13] Tail Pipe to [8] Over Axle Pipe Assembly and appropriate 2007-2013 [10] Hanger Clamp with no hanger bend, 2014-2019 [11] Hanger Clamp short hanger with bend, or 2020 and up [12] Hanger Clamp long hanger  with bend to existing isolators with supplied [9] Clamp.
STEP 7: Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
STEP 8: Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
BRExhaust recommends professional installation for all products

TABLE 1.

Vehicle Configuration| 2014-2016| 2017-2019| 2020
Crew Cab/Long Bed| 26.50″| 16.25″| 31.00″
Crew Cab/Standard Bed| 13.25″| 3.00″| 4.50″
Double Cab/Long Bed| 18.40″| 8.15″| –
Double Cab/Standard Bed| 4.50″| N/A|
| TABLE 2.
---|---
Item| Hanger| 2007-2013| 2014-2019| 2020
31519| 4.00″ Band Clamps| X| X| X
7| U-Bolt Hanger Short| | | X
6| U-Bolt Hanger Long| X| X|
10| Torca Hanger Clamp Rr No Bend| X| |
ii| Torca Hanger Clamp Rr Short w/Bend| | X|
12| Torca Hanger Clamp Rr Long w/Bend| | | X

BRExhaust 106-0751 Direct Fit Replacement Exhaust System -
feager

WARNING:
When working on, under, or around any vehicle exercise caution.
Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult vehicle manual for correct lifting specifications. Always wear safety glasses and  ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
BRExhaust recommends professional installation for all products

BRExhaust logo Technical Support: 1-800-631-7271
BRExhaust — 1901 Corporate CTRL, Oceanside, CA 92056
www.brexhaust.com
REV #000 DATE 5/9/2023

Documents / Resources

| BRExhaust 106-0751 Direct Fit Replacement Exhaust System [pdf] Instruction Manual
106-0751 Direct Fit Replacement Exhaust System, 106-0751, Direct Fit Replacement Exhaust System, Fit Replacement Exhaust System, Replacement Exhaust System, Exhaust System
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals