BRExhaust 106-0754 Direct-Fit Exhaust Instruction Manual
- June 13, 2024
- BRExhaust
Table of Contents
BRExhaust 106-0754 Direct-Fit Exhaust
Product Information
The product is an exhaust system designed for vehicles. It includes various components such as an inlet pipe assembly, over axle pipe assembly, muffler tail pipe assembly, and clamps.
- Manufacturer: BRExhaust
- Part Number: 106-0754
- Installation Instructions: Yes
- Technical Support: 1-800-631-7271
- Manufacturer’s Address: 1901 Corporate Ctr, Oceanside, CA 92056
- Website: www.brexhaust.com
Revision Number: #000
Date: 5/8/2023
Product Usage Instructions
-
Carefully read all instructions before installation.
-
Disconnect the vehicle’s battery before removing the OEM
exhaust system to prevent electrical accidents and reset the computer if applicable. -
Remove the existing exhaust system from the vehicle, only removing the parts that will be replaced.
-
Clean the existing flange with a wire brush to ensure proper sealing.
-
Attach the Inlet Pipe Assembly to the existing exhaust and existing isolator using the supplied clamp.
-
Attach the Over Axle Pipe Assembly to the Inlet Pipe Assembly and existing isolator using the supplied clamp.
-
Attach the Muffler Tail Pipe Assembly to the Over Axle Pipe Assembly and existing isolator using the supplied clamp.
-
Ensure that the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
-
Tighten all clamps starting from the rear of the vehicle. Do not exceed 30ft-lb when tightening the clamp. Check all clamps after 50 miles and retighten if necessary.
Warning: When working on, under, or around any vehicle, exercise caution. Allow the vehicle’s exhaust system to cool before removal to avoid severe burns from exhaust temperatures. If working without a lift, always consult the vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Failure to follow safety measures could result in serious injury or death.
Note: Professional installation is recommended for all products.
INSTALLATION INSTRUCTIONS
-
STEP 1:
(Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing. -
STEP 2:
Attach [2] Inlet Pipe Assembly to existing exhaust and existing isolator with supplied [1] Clamp. -
STEP 3:
Attach [4] Over Axle Pipe Assembly to [2] Inlet Pipe Assembly and existing isolator with supplied [3] Clamp. -
STEP 4:
Attach [6] Muffler Tail Pipe Assembly to [4] Over Axle Pipe Assembly and existing isolator using supplied [5] Clamp. -
STEP 5:
Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain. -
STEP 6:
Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
WARNING:
When working on, under, or around any vehicle exercise caution. Please
allow the vehicle’s exhaust system to cool before removal, as exhaust
temperatures may cause severe burns. If working without a lift, always consult
vehicle manual for correct lifting specifications. Always wear safety glasses
and ensure a safe work area. Serious injury or death could occur if safety
measures are not followed.
BRExhaust recommends professional installation for all products
Technical Support: 1-800-631-7271
BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>