BRExhaust 106-0366 Ito Direct Fit Exhaust Kit Instructions
- June 13, 2024
- BRExhaust
Table of Contents
BRExhaust 106-0366 Ito Direct Fit Exhaust Kit
Product Information
| Part No. | Description |
|---|---|
| 168084 | Item 1 – Nuts and bolts (not included) |
| 168359 | Item 2 – Exhaust isolators |
| 167507 | Item 3 – Clamps |
| 168358 | Item 4 – Slip fit |
Product Usage Instructions
- Carefully read all instructions before installation.
- Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and reset the computer if applicable to the vehicle.
- Remove the existing exhaust system from the vehicle. Only remove parts that will be replaced.
- Clean the existing flange with a wire brush to ensure proper sealing.
- Attach item 2 (exhaust isolators) to the existing isolators and exhaust with item 1 (nuts and bolts not included).
- Attach item 4 (slip fit) to the existing isolators (item 2) with item 3 (clamps).
- Connect item 2 (slip fit) with the clamps provided.
- Ensure the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
- Tighten all clamps starting from the rear of the vehicle. Do not exceed 30 ft-lb when tightening clamps. Check all clamps after 50 miles and retighten if necessary.
WARNING:
- When working on, under, or around any vehicle, exercise caution.
- Allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns.
- If working without a lift, always consult the vehicle manual for correct lifting specifications.
- Always wear safety glasses and ensure a safe work area.
- Serious injury or death could occur if safety measures are not followed.
BRExhaust recommends professional installation for all products.
- Technical Support: 1-800-631-7271
- BRExhaust: 1901 Corporate Ctr, Oceanside, CA 92056 www.brexhaust.com
PART NO. 106-0366
BILL OF MATERIALS:
- 168084
- 168359
- 167507
- 168358
INSTALLATION INSTRUCTIONS
-
STEP 1:
(Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing. -
STEP 2:
Attach item 2 to existing isolators and exhaust with item 1 (nuts and bolts not included) -
STEP 3:
Attach item 4 to existing isolators item 2 with item 3 -
STEP 4:
Connect item 2 slip fit with clamps provided -
STEP 5:
Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain. -
STEP 6:
Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
WARNING:
When working on, under, or around any vehicle exercise caution. Please allow
the vehicle’s exhaust system to cool before removal, as exhaust temperatures
may cause severe burns. If working without a lift, always consult vehicle
manual for correct lifting specifications. Always wear safety glasses and
ensure a safe work area. Serious injury or death could occur if safety
measures are not followed.
BRExhaust
recommends professional installation for all products
Technical Support: 1-800-631-7271
BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056
www.brexhaust.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>