BRExhaust 106-0252 Direct Fit Exhaust Kit Instruction Manual

BRExhaust 106-0252 Direct Fit Exhaust Kit

Product Information

The product being installed is the exhaust system, part number 106-0252. The bill of materials for the installation includes the following parts:

• 1 x 167860
• 1 x 167876
• 1 x 167794
• 1 x 169305
• 1 x 168106
• 1 x 167643
• 1 x 168107

Product Usage Instructions

1. Carefully read all instructions before installation.
2. Disconnect the vehicle’s battery before removing the OEM exhaust system to prevent electrical accidents and reset the computer if applicable.
3. Remove the existing exhaust system from the vehicle, only removing the parts that will be replaced.
4. Clean the existing flange with a wire brush to ensure proper sealing.
5. Attach item 3 to the existing exhaust using items 1 and 2.
6. Connect item 5 to the existing isolator and item 3 using item 4.
7. Connect item 7 to item 5 using item 6 (nuts and bolts not included).
8. Ensure that the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
9. Tighten all clamps starting from the rear of the vehicle. Do not exceed 30 ft-lb when tightening clamps. Check all clamps after driving for 50 miles and retighten if necessary.

Warning:

When working on, under, or around any vehicle, exercise caution. Allow the vehicle’s exhaust system to cool before removal to avoid severe burns from exhaust temperatures. If working without a lift, always consult the vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Failure to follow safety measures could result in serious injury or death.
BRExhaust recommends professional installation for all products.

Technical Support: 1-800-631-7271
BRExhaust: 1901 Corporate Ctr, Oceanside, CA 92056
Website: www.brexhaust.com

PART NO. 106-0252

**BILL OF MATERIALS

**

1. 167860
2. 167876
3. 167794
4. 169305
5. 168106
6. 167643
7. 168107

INSTALLATION INSTRUCTIONS

• STEP 1:
  (Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean the existing flange with a wire brush to ensure proper sealing.
  STEP 2:
  Attach item 3 to the existing exhaust with items 1 and 2

• STEP 3:
  Connect item 5 to the existing isolator and item 3 with item 4

• STEP 4:
  Connect item 7 to item 5 with item 6 (nuts and bolts not included)

• STEP 5:
  Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.

• STEP 6:
  Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING THE CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)

WARNING:

When working on, under, or around any vehicle exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
BRExhaust recommends professional installation for all products

Technical Support: 1-800-631-7271
BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056
www.brexhaust.com

References

• MagnaFlow Exhaust, Mufflers & Cat Converters - Quality. Power. Sound.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>