BEGA 12065.1 LED Recessed Ceiling Downlight Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 12065.1 LED Recessed Ceiling Downlight
Product Information
Product Usage Instructions
Dimensions
Product Description
Safety
Installation
Maintenance
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 12065.1 LED Recessed Ceiling Downlight

Product Information

The product is a luminaire with a focalization/diffusion lens. It has a module designation of 12 065.1 K3 and a colour temperature of 3000 K. The color rendering index (CRI) is greater than 90. The module luminous flux is 2820 lm, and the luminaire luminous flux is 2132 lm. The luminaire has a luminous efficiency of 101.5 lm/W.

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer is not liable for damage caused by improper use or installation. If modifications are made to the luminaire, the person responsible for the modifications will be considered the manufacturer. The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components, which can be found on the manufacturer’s website at www.bega.com.

Product Usage Instructions

To clean the luminaire, regularly use solvent-free cleansers to remove dirt.

If you need to replace the LED module, follow these steps:

Note the designation of the LED module on the label inside the luminaire.
Disconnect the system and open the luminaire.
Follow the installation instructions for the LED module.
Inspect and replace the luminaire gaskets if necessary.
Replace any defective glass.
Close the luminaire.

The power supply units provided, 13 202 for on/off and 13 174 for DALI, are only suitable for the operation of one LED luminaire. For installation housing and accessories, separate instructions for use can be provided upon request.

Dimensions

BEGA-12065-1-LED-Recessed-Ceiling-Downlight-fig-1

Application

Recessed ceiling luminaire · indoor luminaire with hand-blown crystal glass and metal housing for connection to external LED power supply unit.
A focusing / dispersing lens bundles the powerful LED light in the centre of the reflector for a direct proportion of downlight. At the same time, a proportion of the dispersed light is used to illuminate the luminaire glass and to generate the vertical illuminance.
For installation into ceilings with a shallow depth in interior areas.

Product Description

Luminaire housing made of metal
Ceiling trim ring made of metal, Colour white
Crystal glass with screw neck
Additional focusing / diffusing lens made of partially frosted crystal glass
Reflector made of pure, high-gloss anodized aluminium
Silicone gasket
Fixing is achieved by using two adjustable wedge-shaped claws
Connecting cable with strain relief and plug connector system for BEGA power supply unit, on/off or DALI.
Safety class III
CE: Conformity mark
Weight: 0.9 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage: 17.5 W
Luminaire connected wattage: 21 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 50 °C
When installed in heat-insulating material: ta max = 25 °C

12 065.1 K3

Module designation: LED-0327/930
Colour temperature: 3000 K
Colour rendering index: CRI > 90
Module luminous flux: 2820 lm
Luminaire luminous flux: 2132 lm
Luminaire luminous efficiency: 101,5 lm / W

Lighting technology

Half beam angle 38°

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
A separate power supply unit is required to operate the luminaire.
For connection to external LED-power supply unit – accessory 13 202 or 13 174 – the luminaire is equipped with a 2-pin connector.
Note operating instructions of the LED-power supply units.

Please note: The black marked connector is not used to connect to the power supply unit 13 202 on/off.

The recessed opening is covered by the frame of the luminaire housing.
Fixing of the luminaire in the structure is achieved by using two adjustable wedge-shaped claws.

Installation into concrete ceilings

For this purpose installation housing 13 018 is available.

Installation into inserted ceilings

A recessed opening of ø 208 mm is necessary to accept the luminaire housing.
Recessed depth min. 45 mm.
The lateral distance between recessed luminaire and other building parts must be at least 50 mm.
The claws catch the ceiling facing from the back side. Minimum thickness of the ceiling facing is 5 mm. If the ceiling facing has a thickness of less than 10 mm or in case of an installation into plasterboard ceilings, the facing thickness in the region of the claws must be increased from the back side.

Open luminaire

Remove glass from luminaire housing by turning it counter-clockwise.
Connect plug part of the luminaire with power supply unit.
Push external LED power supply unit and luminaire housing into the ceiling cut-out.
Luminaire housing and external LED power supply unit must not be installed in heat-insulating material.
Tighten evenly screws of claw fasteners.
Impress the enclosed cover ring about the sealing ring onto the glass.
Make sure that the sealing ring is seated correctly!
Slide enclosed – separately packed – dispersing lens into the reflector.
Screw glass with cover ring and dispersing lens into the luminaire housing.

Maintenance

Cleaning /Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Accessories

Power supply units for LED luminaires
220-240 V · 0/50-60 Hz with strain relief and plug connector system.
13 202: Power supply unit on/off
13 174: Power supply unit DALI
The power supply units are only suitable for the operation of one LED luminaire.
13 018: Installation housing

For the accessories a separate instructions for use can be provided upon request.

Spares