ricoo TS4311 Dual Monitor Mount Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo TS4311 Dual Monitor Mount
Product Information
- Product Name: TS4311 Version: v.21.01 Maximum
- Load Weight: 7kg (15.4lbs)
- Manufacturer: E.N.Z. Engineering GmbH
- Address: Salzmatten 6, 79341 Kenzingen (Germany)
- Email: support@ricoo.de
- Website: www.ricoo.eu
Scope of Delivery
– B x1 -C x2 – D x2 – A x1 – E x1 – F x4 – G x1 – H x1 – I x1 – J x1 – K x2 – L x2 – M3x8 – M x2 – M6x16 – N x8 – M6x14 – O x1 – P x1 – M-A x8 – M4x12 – M-B x8 – M4x16 – M-C x8 – M5x12 – M-D x8 – M5x16 – M-E x8 – M-F x8
Product Usage Instructions
-
Check VESA Mounting Hole Distance: – Before installation, check the distance between the VESA mounting holes on your display. – This screen mount supports VESA hole distances in the minimum and maximum ranges of 75x75mm and 100x100mm respectively. – VESA Hole Distance refers to the distance between the mounting holes on the back of the screen.
-
Assembly Steps: a) Attachments: – Attach part A to the top of the mount. – Attach parts B, C, D, E, and F as indicated in the diagram. b) Mounting the Screen: – Ensure the VESA mounting holes on the back of your screen match the supported hole distances. –
Use the provided screws (M6x16 or M6x14) to attach the screen to the mount using the appropriate VESA holes. – If the screws (M-B, M-D) are too long, use the plastic spacers (M-F) as shown in Step 6 A. -
Adjustments: – Use parts G, H, I, J, K, L, M-A, M4x12, M-B, M4x16, M-C, M5x12, M-D, M5x16, M-E, and M-F as indicated in the diagram to adjust the mount according to your desired positioning.
-
Finalizing Installation: – Once the adjustments are made, ensure all components are securely tightened. – Double-check the load weight of your screen does not exceed the maximum weight limit of 7kg (15.4lbs). – Ensure all connections are stable and secure.
Note: Exceeding the listed load weight may result in property damage or serious injury.
For further assistance or support, please contact E.N.Z. Engineering GmbH via email at support@ricoo.de or visit their website at www.ricoo.eu.
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Scope of delivery
We recommend using a professional level.
Please check BEFORE installation distance between VESA mounting holes on your display!
This screen mount supports VESA hole distance in the minimum and maximum distance ranges given above.
VESA – Hole distance = Distances between the mounting holes on the screen back.
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION AND ASSEMBLY
-
Please note: Images in these assembly instructions are only technical presentation of the product. Actual product design may vary minimally.
Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. -
If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
-
This product was designed to be installed and used ONLY as specified in this manual.
-
Improper installation of this product may cause damage or serious injury.
-
This product may only be assembled / installed by the technical staff.
-
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
-
Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged.
-
In case of doubt request for help from an expert. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Tighten screws firmly, but do not over tighten. Over tightening can cause damage the items, this greatly reduces their holding power.
-
By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws which are
numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types. -
When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder. If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.
ASSEMBLY INSTRUCTION
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>