BEGA 51190.4 LED Llluminated Mirror Instruction Manual

BEGA 51190.4 LED Llluminated Mirror

Product Information

are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients, it is recommended to use separate overvoltage protection components.
Safety| The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer does not accept liability for damage caused by improper use or installation. Any subsequent modifications to the luminaire should be done by the person responsible for those modifications.
Lamp| The luminaire uses LED lamps with the following specifications:
– Module designation: LED-1301/930
– Colour temperature: 3000 K
– Colour rendering index (CRI): > 90
– Module luminous flux: 4200 lm
– Luminaire luminous flux: 759 lm
– Luminaire luminous efficiency: 25.3 lm / W
Installation| Please follow these steps for installation:
1. Avoid touching the light output opening of the LED directly during installation or relamping.
2. Remove the luminaire housing (reflector) from the packaging.
3. Pass the power connecting cable through the cable entry into the luminaire housing.
4. Secure the luminaire housing to the installation surface using the provided fixing materials or other suitable materials.
Replacing the LED Module| To replace the LED module, follow these steps:
1. Disconnect the system and open the luminaire.
2. Refer to the installation instructions for the LED module and
follow them carefully.
3. If the luminaire cover is defective, it must be replaced.
4. Close the luminaire after completing the replacement.

Application

• Illuminated mirror · Indoor luminaire with velvet black metal housing.
• Luminaire with light source shielded to the front and metallic inside colour of the reflection surface.
• Radial light emission 360°.

Product Description

• Luminaire housing made of aluminum, surface Colour velvet black inside hue matt brass
• Inside the synthetic cover, translucent white
• Mirror made of crystal glass, diameter 400 mm, visible edge polished 4 mounting holes ø 6 mm
• Distance 260 mm
• 2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@
• Connection terminal 2.5@
• Earth conductor connection 2-pole connecting terminal for digital control
• LED power supply unit 220-240 V x 0/50-60 Hz
• DC 196-250 V
• DALI-controllable
• Number of DALI addresses: 1
• Basic insulation is provided between the mains and control cables BEGA Thermal Control®
• Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
• Safety class I
• Protection class IP 44
• Protected against granular foreign bodies ≥ 1 mm and splash water
  • Conformity mark
• Weight: 6.1 kg
• This product contains light sources of energy efficiency class(es) D

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp Specification

• Module connected wattage 27 W
• Luminaire connected wattage 30 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 50 °C

51 190.4 K3

• Module designation LED-1301/930
• Colour temperature 3000 K
• Colour rendering index CRI > 90
• Module luminous flux 4200 lm
• Luminaire luminous flux 759 lm
• Luminaire luminous efficiency 25,3 lm / W

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Remove the luminaire housing (reflector) from the packaging.
• Pass the power connecting cable through the cable entry into the luminaire housing.
• Secure the luminaire housing to the installation surface with the fixing materials provided or other suitable materials.

• Note position of application of the luminaire housing “arrow down”.
• Connect the earth conductor to the earthing screw of the luminaire housing.
• Remove the mounting plate with LED unit from its packaging.
• Loosen 4 Torx screws (T 20) and remove the central service panel from the LED unit.
• Loosen earth connection (plug connection) between central service panel and LED unit.
• Guide wires of the power connecting cable through the rear opening into the LED unit.
• Place the LED unit over the keyholes onto the four threaded bolts of the luminaire housings and turn it clockwise until it stops.
• Tighten the hex nuts M5 over the keyholes.
• Make the electrical connection to the terminals.
• Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
• The two connecting terminals marked DA, DA are provided for digital control purposes.
• If these terminals are not assigned, the luminaire will work with full light output.
• Establish the earth conductor connection of the LED unit to the luminaire housing (plug connector).
• Make earth connection (plug connection) from the central service panel to the LED unit again.
• Place the central service panel back onto the LED unit and fasten using the 4 Torx screws (T20).
• Remove the mirror from its packaging.
• Place the rear locking bolts of the mirror fastening onto the 3 elongated recesses of the LED unit.
• Turn the mirror clockwise against the resistance until the locking bolts audibly click into their final position.

Dimension

Cleaning And Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the system and open the luminaire.
• Please follow the installation instructions for the LED module.
• The defective luminaire cover must be replaced.
• Close the luminaire.

Spares

• LED power supply unit DEV-0305/700i
• LED module 3000 K LED-1301/930
• Mirror 75 005 089
• Reflector 75 005 253

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com.

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>