quartet Dry-Erase and Bulletin Board Instruction Manual
- June 9, 2024
- quartet
Table of Contents
Dry-Erase and Bulletin Board
Installation Instructions
Hardware Kit
Tools Required
– Tape Measure
– Phillips Screw Driver
– Pencil
– Hammer
– Drill (1/4″,1/8″ Bit)
EURO ALUMINUM FRAME BOARD
*Mounting Instructions
NOTE** – For Dry-Erase Boards:
Before mounting board to wall, please refer to instructions in “Accessory Kit”
to attach the marker tray to the board frame.
Step 1
Determine board location. To position top hanging brackets, mark center hole
of hanger 6″ from outside edge of board and 1-3/8″ down from top of board (A).
Drill holes for each hanger in marked locations using a 1/4″ drill bit. Insert
wall anchors into holes flush with the wall.
Insert screws through hanging brackets into the wall anchor (B). Tighten
firmly. Holding the board at (approx.) 15° angle, place the channel in the
back of the frame over the wall hangers. Lower the board so itis flush to the
wall (C).
Step 2
Remove bottom plastic corner caps (D), mark wall through top hole of each
corner (E). Remove board from wall, drill holes at pencil marks. Install
plastic wall anchors. Re-hang board and insert No. 10 screw through plastic
comer and into wall anchor (F). Tighten firmly. Replace corner caps by
pressing into place over the screws. (L-Bracket & Truss Head Screws are not
required.)
ALUMINUM FRAME BOARD
*Mounting Instructions
NOTE** – For Dry-Erase Boards:
Before mounting board to wall, please refer to instructions in“Accessory
Kit”to attach the marker tray to the board frame.
Step 1
Determine board location. To position top hanging brackets, mark center hole
of hanger 6″ from outside edge of board and 7/8″ down from top of board
(A). Drill holes for each hanger in marked locations using a 1/4″ drill
bit. Insert wall anchors into holes flush with the wall.
Insert screws through hanging brackets into the wall anchor (B). Tighten
firmly. Holding the board at (approx) 15° angle, place the channel in the back
of the frame over the wall hangers. Lower the board so itis flush to the wall
(C).
Step 2
To position bottom “L” brackets, mark wall 1-5/8″ up from bottom of board 6″
from each outside edge (D). Drill holes in marked locations using a 1/4″ drill
bit. Insert wall anchors into holes flush with wall. Insert screws through “L”
brackets into wall anchors (E). Hang board and mark frame through hole in each
“L” bracket. Remove board and drill pilot hole at each mark with 1/8″ drill
bit. Re-hang board and insert #8 x 1/2″ truss head screw through each “L”
bracket and into pilot holein frame (F).Tighten firmly.
WOOD FINISH FRAME BOARD
*Mounting Instructions
“NOTE** – For Dry-Erase Boards:
Before mounting board to wall, please refer to instructions in“Accessory
Kit”to attach the marker tray to the board frame.
Step 1
Determine board location. To position top hanging brackets, mark center hole
of hanger 6″ from outside edge of board and 1-5/8″ down from top of board (A).
Drill holes for each hanger in marked locations using a 1/4” drill bit. Insert
wall anchors into holes flush with the wall.
Insert screws through hanging brackets into the wall anchor (B). Tighten
firmly. Place the channel in the back of the frame over the wall hangers. Push
top of frame down until board is fully engaged on hangers (C).
Step 2
To position bottom “L” brackets, mark wall 2-1/2″ up from bottom of board 6
from each outside edge (D). Drill holes in marked locations using a 1/4″ drill
bit. Insert wall anchors into holes flush with wall. Insert screws through “L”
brackets into wall anchors (E). Hang board and mark frame through hole in each
“L” bracket. Remove board and dill pilot hole at each mark with 1/8″ drill
bit. Re-hang board and insert #8 x 1/2″ truss head screw through each “L”
bracket and into pilot holein frame (F). Tighten firmly.
Accessory Kit/ Marker Tray
Installation Instructions
ISA1_REV.2
Tool Required
Phillips Screw Driver
Parts
| |
---|---|---
Left and right Tray End Caps (1 X)| No. 6-32 x 3/8″ Screw (2 X)| No. 8 x 1″
Screw (5 X)
To Attach Marker Tray – ALUMINUM FRAME BOARDS
Step 1: Center marker tray along the bottom board frame (horizontal or vertical orientation).
Step 2: Insert marker tray at an angle into back channel of board frame.
Rotate tray up until itis fully engaged.
Step 3: Align tray end caps and fasten with No.6-32 x 3/8″ screws
To Attach Marker Tray – WOOD FINISH FRAME BOARDS
Step 1: Align holes in marker tray with pilot holes in bottom board frame Note: Pilot holes for tray are in long side of board only. Drill (3) 7/16″ diameter pilot holes in short side of frame for vertical mounting.
Step 2: Insert #8 x 1″ truss head screws through holes in tray and into board frame. Tighten firmly.
For questions about board and marker tray installation, please call Quartet Customer Service at 800-541-0094
ACCO Brands (Retums Center)
101 Bolton Ave 9E
Booneville, MS 38829 USA
Tel:800-541-0094
www.acco.com
www.quartet.com
AccoKitBVsm_REV.5
Documents / Resources
|
quartet Dry-Erase and Bulletin
Board
[pdf] Instruction Manual
Dry-Erase and Bulletin Board, Bulletin Board, Board
---|---