PRESIDENT 930816 Remote BT Mike Owner’s Manual

PRESIDENT 930816 Remote BT Mike

OVERVIEW

Box contents

STEERING WHEEL CONTROL INSTALLATION

• Wrap the bracket on the steering wheel (see fig. A1) in the position of your choice.
• Pull the strap around the steering wheel. Pull on the strap until the bracket can no longer be turned.
• Attach the strap to the 2 small lugs (see fig. A2).
• Place the retainer on the lugs (see fig. A3 and A4).
• The steering wheel control bracket is fixed.
• Slide the control as shown in fig. A5.

REMOVING THE CONTROL FROM ITS BRACKET

• Using your fingernail, pull apart the retaining lug (see fig. A6 point 1).
• Remove the control unit (see fig. A6 point 2).

DONGLE INSTALLATION / REMOVAL

• Plug in / remove the dongle from your CB PRESIDENT as shown in Fig. B1.

OPERATING YOUR REMOTE BT MIKE

• Switch on your CB PRESIDENT.
• The dongle LED flashes red once every 5 seconds.
• Set the switch [7] on the steering wheel control to me. “POWER ON” is announced.
• “CONNECTED” is announced once the control is connected to the dongle.
• The dongle LED flashes green once every 5 seconds. (otherwise see §5)

CHANNEL SELECTOR

• These keys [2] and [3] allow you to move up or down a channel.
• You can reverse up/down to adapt it to the chosen position.
• To do this, press and hold the button that will be assigned to down and start (switch on l)

PTT (Push To Talk)
The PTT button [1] on the steering wheel control can be set to 2 modes:

MODE 1 (default): Press PTT [1] once to talk. Press a second time to receive a message.

• To activate this mode:
  • Presented a button me and un on. de 1 is active.

MODE 2: Press and hold to speak. Release to return to reception.

• To activate this mode:
  • Press and hold buttons [3] and [1] for 2 seconds.
  • The green LED flashes 3 times and turns off. Mode 2 is active.

NRC SETTING
Your REMOTE BT MIKE is equipped with NRC technology with 5 levels of adjustment.
To enter configuration mode:

• On the steering wheel control, press buttons [2] and [3] for 2 seconds.
• The current setting is displayed.
• Use button [2] or [3] to change the current setting.
• The current setting is saved.
• If no button is pressed for 10 seconds, you exit the parameter-setting mode. The current setting is saved.

CHARGING
Plug one end of the USB cable into the connector [6] and the other into the USB port on your CB PRESIDENT, if fitted, or on your vehicle.

• Steady red light [4]: charging.
• Steady green light [4]: charging complete.

When the battery is discharged, “DISCHARGED” is announced every 5 minutes and the red LED flashes twice every 5 seconds.

APPAIRING
The steering wheel control and dongle are supplied paired.
If you need to replace one of the two components, here’s how to pair them.

• Connect the dongle to your PRESIDENT transceiver.
• Press the button [8] briefly.
• The button will flash alternately red and green. The dongle is in pairing mode.
• Keep the control within 5m of the dongle.
• On the steering wheel control, press the PTT key [1]. LED [4] starts flashing red and green and “PAIRING” is announced. The control unit is in pairing mode.
• When pairing is complete, the LED turns off.

6-PIN MICROPHONE PLUG

Zasilanie

BATTERY LOCATION

WARRANTY (Under the warranty conditions in the country of purchase)

• Important: Proof of original purchase is required for warranty service.
• WARRANTOR: GROUPE PRESIDENT ELECTRONICS (“PRESIDENT”)

ELEMENTS OF WARRANTY: PRESIDENT warrants, to the original user, if purchased from a retail store, that this PRESIDENT product will be free from defects in materials and craftsmanship, subject to the limitations and exclusions as set out below.
This warranty extends only to the original user. The warranty will be invalid if the Product is (A) damaged or has not been maintained in good condition through reasonable maintenance, (B) has been modified, altered or used as part of any conversion kits, subassemblies, or any configurations not sold by PRESIDENT, (C) improperly installed, (D) serviced or repaired by someone other than an authorized PRESIDENT service centre for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by PRESIDENT, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this product.

STATEMENT OF REMEDY: If the product does not conform to this warranty at any time while this warranty is in effect, the warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by the warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND

ENTIRE WARRANTY

ABOUT THE PRODUCT AND IS INSTEAD OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some countries do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights that vary from country to country.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). The Product should include all parts and accessories originally packaged with the Product. Include proof of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to the warrantor at

Groupe PRESIDENT ELECTRONICS

• Route de Sète – BP 100
• 34540 BALARUC
• FRANCE

Group PRESIDENT ELECTRONICS

• 1007 Collier Center Way,
• Naples, Florida 34110
• USA

The declaration of conformity is available at the following internet address: https://president-electronics.com/DC/ACFD602

CONTACT

• Head Office/Siège Social: USA – 1007 Collier Center Way, Naples, Florida 34110
• Web: http://www.president-electronics.us
• Email: info@president-electronics.us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>