BEGA 51061.1 Track Spotlight for Indoor Use Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
Track spotlight for indoor use
51 061.1
Instructions for use
Application
Ceiling mounted track spotlight · indoor luminaire for 3-phase Euro standard-
Plus ® track systems. The optical system of the washer is swivel mounted and
rotatable.
Symmetrical wide beam light distribution. Optical diffuser filters are
available as accessories for changing the light distribution. With BEGA Hybrid
Optics® : Highly efficient and low-loss light distribution, thanks to
reflector and optical lens.
Product description
GENIUS Track spotlight with adapter Cast aluminum luminaire housing, finish
Color velvet white, Polycarbonate track adapter with integrated LED power
supply unit Trim ring · Chrome finish Safety glass, with internal optical
diffuser filter Optical silicone lens · BEGA Hybrid Optics ® Reflector surface
made of pure aluminum LED power supply unit
220-240 V ~ 50/60 Hz DALI-controllable Basic insulation is provided between
the mains and control cables
Safety class II 
****– Conformity mark
Weight: 1.1 kg
This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 31.6 W |
|---|---|
| Luminaire connected wattage | 37.5 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 35 °C |
51 061.1 K3
| Module designation | LED-0800/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 4220 lm |
| Luminaire luminous flux | 3010 lm |
| Luminaire luminous efficiency | 80,3 lm / W |
51 061.1 K4
| Module designation | LED-0800/930 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 4285 lm |
| Luminaire luminous flux | 3056 lm |
| Luminaire luminous efficiency | 81,5 lm / W |
Light technique
Track spot · surface washer with adjustable optical system.
Optical system 0-340° swivel-mounted and ± 310° infinitely rotatable around
the vertical luminaire axis.
Symmetrical wide beam light distribution.
Half beam angle 36°
The symmetrical light cone can be changed to a flat beam, symmetrically
diffuse or asymmetrical light distribution for special lighting applications
by replacing the optical diffuser filter (standard) – accessoires.
For flat beam light distribution: Diffusing filter 13 288
For symmetrical diffuse light distribution: Diffusing filter 13 312
For asymmetrical light distribution: Diffusing filter 13 311
| | | 
---|---|---|---
standard| flat beam| symmetrically diffuse| asymmetrical
The light cone can be adjusted by ±360° by turning the trim ring.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
The track spotlight with adapter is ready for operation in 3-phase
EUROSTANDARD-PLUS® track systems.
The mounting is done without tools in the bus bar.
IMPORTANT:
Ensure that the adapter’s two lateral stays are located on the same side as
the matching guide profile of the track before installing the adapter in the
3-phase EUROSTANDARDPLUS ® track system.
To select the phase ( 1 2 3 ) the turning knob on the rear side of the adapter
has to be operated accordingly.
Screw enclosed fastening ring (a) with attached reflector into the luminaire
housing by turning it clockwise until it stops, so that it is fixed by
clamping.
Clip the trim ring with glass and internal optical diffuser filter (b) onto the luminaire housing by applying slight pressure.
Place the surface washer adapter flush on the conductor rail in the desired
position.
Push the two fixing levers on the underside of the adapter to the right until
they click into their end position.
Set the desired LED beam direction by turning and tilting the luminaire
housing.
Move the two fixing levers in opposite directions until they disengage to
unlock the adapter.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The replacement can be carried out by
a qualified person using standard tools.
Disconnect the system and open the luminaire.
Uninstall the reflector.
Please follow the installation instructions for the LED module.
Install the reflector. Defective glass must be replaced. Close the luminaire.
Accessories · Optical diffuser filter
13 288 Diffuser filter flat beam
13 312 Diffuser filter symmetrical, diffuse
13 311 Diffuser filter asymmetrical
For the accessories a separate instructions for use can be provided upon request.
Spares
| Prismatic film | 15 000 684 |
|---|---|
| Fastening ring reflector | 20 000 086 B5 |
| LED power supply unit | DEV-0437/900i |
| LED module 3000 K | LED-0800/930 |
| LED module 4000 K | LED-0800/940 |
| Trim ring with glass | 75 004 844 |
| Reflector unit | 76 001 608 .1M |
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>