BEGA 50302 Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
50302 Wall Luminaire
Instruction Manual
50302 Wall Luminaire
Technical amendments reserved
Ceiling and wall luminaire for indoor use
Instructions for
use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.
Product description
Metal housing, finish Colour white Hand-blown opal glass, satin matt 2
mounting holes ø 6mm Distance apart 180mm 2 cable entries for through-wiring
for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@ Earth
conductor connection
LED power supply unit 220-240 V x 0/50-60 Hz BEGA Thermal Switch® Temporary
thermal shutdown to protect temperature-sensitive components Safety class I
Impact strength IK03 Protection against mechanical impacts < 0.35 joule –
Safety mark – Conformity mark Weight: 2.2 kg This product contains light
sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability fordamage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components. You can find them on our website
at www.bega.com.
Lamp
| Module connected wattage | 15.1 W |
|---|---|
| Luminaire connected wattage | 17.6 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 45 °C |
50 302 K27
| Colour temperature | 2700 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2535 lm |
| Luminaire luminous flux | 1839 lm |
| Luminaire luminous efficiency | 104,5 lm / W |
50 302 K3
| Colour temperature | 3000 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2570 lm |
| Luminaire luminous flux | 1865 lm |
| Luminaire luminous efficiency | 106 lm / W |
Notice prior to installation:
Luminaire with trim frame The luminaire housing must be inserted in the trim
frame (accessory) before it is mounted onto the mounting surface.
Make sure that the two openings in the trim frame coincide with the positions
of the grub screws of the luminaire housing.
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Lead mains supply cable through the cable entry into the luminaire housing.
Fix the luminaire housing with enclosed or any other suitable fixing material
onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth and electrical connection to the terminal.
Position the
glass over the luminaire housing so that the retaining springs fit into the
two recesses in the raised edge of the glass.
Press the glass against the retaining springs at a flat angle as far as it
will go and push it into the luminaire housing (see drawing).
Gentle pressure on the glass will fix it in the luminaire housing through the
three lobes on the opposite side.
IMPORTANT: If the luminaire is to be installed on the ceiling, it is essential that the two grub screws (Allen screws) should be screwed with gentle pressure against the retaining springs. In this way, the glass is held securely in place and is resistant to vibration.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Opening the luminaire
Unscrew the two grub screws (Allen screws) of the luminaire housing as far as
they will go.
A recess (identifiable by touch) in the edge of the glass indicates the
direction from which the luminaire glass must be pressed against the spring
pressure of the glass retaining springs in order to release it from the
luminaire housing.
Pull the glass away from the luminaire housing against the holding force of
the retaining springs and remove it.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to
those of the LED units originally fitted. The LED unit can be replaced by
qualified persons using standard tools.
Disconnect the system and open the luminairReplace the LED unit.
Close the luminaire.
A damaged glass must be replaced.
Accessory · Trim frames
For this luminaire metal trim frames in 3 enamel surfaces are optional
available.
Trim frames are accessories and must be ordered separately.
| Part. No
---|---
Colour white| 13 137
Colour palladium| 13 138
Colour glossy silver| 13 139
Spares
| Spare glass | 11 003 279 .0R G |
|---|---|
| LED unit 2700 K | 75 002 257 K27 |
| LED unit 3000 K | 75 002 257 K3 |
BEGA Gantenbrink-Leuchten KG ·
Postfach 31 60 ·
58689 Menden ·
info@bega.com ·
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>