BEGA 33242 Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 33242 Wall Luminaire Instruction Manual
BEGA
Wandleuchte
Wall luminaire
Applique
Instructions for use
Application
Wall luminaire with directed light.
A luminaire with concentrated light distribution downwards which additionally
utilises the reflection properties of the mounting surface.
Product description
Luminaire made of aluminium alloy and stainless steel
BEGA Unidure® coating technology Matt safety glass Silicone gasket
Reflector made of pure anodised aluminium
2 mounting holes ø 5 mm Distance apart 100 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G
1.5@ Connecting terminal and
earth conductor terminal 2.5@ BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I Protection class IP 65
Dust-tight and protection against water jets Impact strength IK06
Protection against mechanical impacts < 1 joule
r – Safety mark c – Conformity mark Weight: 2.0 kg
This product contains light sources of energy efficiency class(es) C
Dark Sky
The light from this luminaire is directed evenly and highly efficiently onto the surface to be illuminated and emits less than 1 % of the luminaire luminous flux into the upper half- space of the luminaire.
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be
carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against
e. g. transients, etc. we recommend separate overvoltage protection
components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage 17.6 W
Luminaire connected wattage 20 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 45 °C
33 242 K3
Module designation LED-0313/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 3340 lm
Luminaire luminous flux 2446 lm Luminaire luminous
efficiency 122,3 lm / W
33 242 K4
Module designation LED-0313/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 3435 lm
Luminaire luminous flux 2516 lm Luminaire luminous
efficiency 125,8 lm / W
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Undo the screws and lift off the luminaire top. Lead the mains supply cable
through the cable entry of the luminaire base.
Note position of application of the luminaire “arrow down”.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied. Make the earth conductor connection
and the electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Make sure that gasket is positioned correctly. Make earth conductor connection
between luminaire top and luminaire base. Replace the luminaire top and
tighten the screws evenly.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified
persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced. Close the luminaire.
Spares __
LED power supply unit DEV-0340/700
LED module 3000 K LED-0313/830
LED module 4000 K LED-0313/840
Reflector 76 001 160
Gasket 83 001 011
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>