BEGA 51 272.6 Wall Luminaire for Indoor Use Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 51 272.6 Wall Luminaire for Indoor Use Instruction Manual
BEGA
Wandleuchte für die Verwendung im Innenbereich
Wall luminaire for indoor use Applique pour utilisation à l’intérieur
Instructions for use
Application
Wall luminaire – Indoor luminaire with ring- shaped light source for
unshielded and uniform light, light-diffusing silicone diffuser and metal
ring.
As single luminaires or in arrangements, they are creative lighting design
solutions for interior design.
Product description
Ring made of metal, finish colour matt copper Luminaire housing made of
synthetic material, finish colour velvet white Round inlay made of metal,
finish colour matt copper
Diffusor made of translucent ageing-resistant silicone
Mounting plate with 2 fixing holes ø 6 mm · 85 mm spacing 2 cable entries for
through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting
terminals 2.5@
Earth conductor connection 2-pole connection terminals for digital control LED
power supply unit 220-240 V x 0/50-60 Hz DC 176-275 V
DALI-controllable Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I c – Conformity mark Weight: 1.0 kg
This product contains light sources of energy efficiency class(es) D
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against
g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Safety
The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Lamp
Module connected wattage 23.2 W
Luminaire connected wattage 26.4 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 50 °C 51 272.6 K3
Module designation LED-1403/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 3600 lm
Luminaire luminous flux 2265 lm Luminaire luminous
efficiency 85,8 lm / W
preliminary data
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Undo the hexagon socket head screw (wrench size 1,5 mm) and remove mounting
plate from luminaire housing.
Pass the power connecting cable through the cable entry in the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface.
Establish earth conductor connection to the earth conductor connection screw
and make the electrical connection to the terminals.
The two connecting terminals marked DA, DA are provided for digital control
purposes.
If these terminals are not assigned, the luminaire will work with full light
output. Insert the connection terminals into the luminaire housing.
Position the luminaire housing in a flat inclination angle over
the fastening edge of the mounting plate and swing in.
Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw
(wrench size 1.5).
If an additional coloured wall accent is desired, arched wall panels made of
metal are optionally available – accessories.
Please note: The installation of a wall
panel should always be carried out after the installation of the luminaire.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Rplacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the system from the power supply. Undo the hexagon socket head
screw (wrench size 2.5 mm) and remove luminaire from mounting plate.
Remove the connecting lines from the terminals and place the front of the
luminaire on a soft surface.Open the luminaire housing:
First loosen the two outer Torx screws (T20), then the 4 inner Torx screws
(T20).
Disconnect the lines of the luminaire cable from the 4 terminals and remove
the terminals.
Using a suitable tool (or with thumb and forefinger), apply pressure to the
four snap-in hooks of the luminaire housing until the housing base releases
from the latch.
Remove the LED module with the diffuser from the holder. Install the
replacement module.
Please follow the installation instructions for the new LED module.
A defective LED-module (silicone diffusor) must be replaced.
Close the luminaire housing:
Place the lower part of the housing on the snap-in hooks of the upper part of
the housing and snap it into place with pressure. First tighten the four inner
Torx screws (T20 max. .2 Nm), then the two outer Torx screws (T20 max. 0.35
Nm).
Re-attach the terminals to the wires of the luminaire cable.
Make the electrical connection to the terminals. Observe the correct
configuration of the connecting cable. Connect the live conductor to the brown
wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control
purposes.
If these terminals are not assigned, the luminaire will work with full light
output. Position the luminaire housing in a flat inclination angle
over the fastening edge of the mounting plate and swing in.
Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw (wrench size 1.5).
Accessories · Wall panels
For this luminaire, optional arched
wall panels made of metal are available in 3 finishes.
Wall panels are accessories and must be ordered separately.
Article number
Colour velvet white 13 337
Colour velvet black 13 339
Colour matt copper 13 340
Spares __
LED power supply unit DEV-0402/700i
LED module 3000 K LED-1403/930
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>