BEGA 66 860 Light Brick Light Brick Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 66 860 Light Brick Light Brick
Product Information
Product Usage Instructions
DIMENSION
Instructions for use
Safety
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 66 860 Light Brick Light Brick

Product Information

Product Description	Luminaire made of aluminium alloy and stainless steel
Earth Conductor Connection	Yes
Lampholder	E 27
Safety Class	I
Protection Class	IP 44 (Protected against granular foreign bodies 1 mm and

splash water)
Impact Strength| IK02
Luminaire Efficiency| 68%

Product Usage Instructions

To ensure safe installation and operation of the luminaire, please follow the instructions below:

The installation and commissioning of this luminaire should only be carried out by a qualified electrician.
Disconnect the electrical installation before performing any maintenance or cleaning.
To clean the luminaire, gently pull the glass out of the spring clips and remove it from the luminaire back housing. Clean the glass and luminaire housing using suitable cleansers that do not contain solvents. Do not use high-pressure cleaners.
To replace the lamp, snap the glass into the lower spring clips, centralize it, and push it into the upper spring clips.
For detailed technical and lighting data, refer to the data sheets available on our website.

Note: The manufacturer does not accept liability for damage caused by improper use or installation. Any modifications made to the luminaire should be performed by a qualified professional.

DIMENSION

BEGA-66-860-Light-Brick-Light-Brick-FIG-1

Instructions for use

Application
Lichtbausteinb Rectangle Wall luminaire for corner mounting.The luminaire is ideal for places where a soft and uniform lighting distribution is required. For interior and exterior applications.
Product description
Luminaire made of aluminium alloy and stainless steel BEGA Unidure® coating technology Opal glass satin matt 1 fixing hole ø 7 mm 1 cable entry for mains supply cable up to ø 10,5 mm Lampholder terminal 2.5@ Earth conductor connection Lampholder E 27 Safety class I Protection class IP 44 Protected against granular foreign bodies ≥ 1 mm and splash water Impact strength IK02 Protection against mechanical impacts < 0.2 joule r – Safety mark c – Conformity mark Weight: 0.85 kg

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible forthese modifications shall be considered the manufacturer.

Lamp3
- Luminaire with screw base E 27
- Lamp output max. 75 W
- This product contains light source of energy
- efficiency class E
Supplied lamp
- BEGA LED lamp 13 584
- LED Retrofit 7 W · 805 lm · 3000 K
- Luminaire efficiency: 68%
- Additional BEGA LED lamps are available for
- this luminaire:
- 13 586 LED 7 W · 805 lm · 3000 K dimmable

Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Installation
Lead the mains supply cable through the cable entry into the luminaire back housing. For wall installation note the position of application »arrow down«. Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface. It is absolutely essential to use the enclosed gasket. Make earth conductor connection. Push silicone sleeves over the lines and make an electrical connection. Insert lamp. Insert the opal glass into the lower spring clips, centralize and push into the upper spring clips.
Relamping · Maintenance
Disconnect the electrical installation. Pull glass out of the spring clips and remove from the luminaire back housing. Clean the glass and luminaire housing using only suitable cleansers. When cleaning please do not use high pressure cleaners. Change the lamp. Snap the glass into the lower spring clips, centralise and push into the upper spring clips.