BEGA 23253.2 LED Wall Luminaire Instruction Manual

Table of Contents

Product description:
Insulating housing with cable entry for temporary thermal shutdown to protect temperature-sensitive components

Material: Mouth-blown opal glass
Safety class: Class I
Protection class: IP 44 (protected against granular foreign bodies of 1 mm and splash water)
Impact strength: IK02 (protection against mechanical impact)
Weight: 1.8 kg
Energy efficiency class(es): D
Overvoltage protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
Lamp module connected wattage: 10.5 W
Rated temperature: 23 253.2 K3
Ambient temperature: 15°C
Module designation: LED-0424/930, LED-0425/930
Colour temperature: 3000 K
Colour rendering index (CRI): >90
Module luminous flux: 1735 lm
Luminaire luminous flux: 1318 lm
Luminaire luminous efficiency: 103 lm/W

Before installation, ensure that the minimum distance of 300 mm is maintained between the removable cap and the wall.
During installation or relamping, avoid touching the light output opening of the LED directly.
To open the luminaire, loosen the knob and remove the cap and glass.
Drill mounting holes into the mounting surface, spacing them 365 mm apart.
Pull apart the power supply cable by a maximum of 15 mm and strip the ends. Connect the protective earth conductor and make the electrical connection.
Attach the luminaire to the mounting surface using the provided or suitable mounting material.
Screw the cap and glass back onto the luminaire to close it. Please refer to the national safety regulations for the installation and operation of this luminaire. Installation and commissioning should only be carried out by a qualified electrician. The manufacturer will not be liable for damage caused by improper use or installation. For additional protection against transients and overvoltage, separate overvoltage protection components are recommended, which can be found on the manufacturer’s website at www.bega.com.

Application

Wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks in interior applications.
They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Luminaire made of Aluminium, finish Stainless steel
Hand-blown opal glass
2 elongated fixing holes
Width 6 mm · 365 mm spacing
Insulating housing with cable entry for mains supply cable up to ø 10,5 mm, max. 3 x 1,5@
Connection terminal 2.5@
Earth conductor connection
LED power supply unit 220-240 V x 0/50-60 Hz
DC 170-276 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water
Impact strength IK02
Protection against mechanical
impacts < 0.2 joule
– Safety mark
CE – Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) D

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

23 253.2 K3

For mounting and dismantling please keep a minimum distance of 300 mm between the removable cap and the wall.
LEDs are high-quality electronic components!Please avoid touching the light output opening of the LED directly during installation or relamping.

Open luminaire:

Loosen knob, remove cap and glass.
Drill mounting holes into the mounting surface – spacing 365 mm.
For the mains supply connecting open the insulation housing – pull open – strip mains supply cable max. 15 mm and lead it into the insulation housing – see sketch.
Make earth conductor connection and electrical connection.
Connect both parts of the insulation housing until they audibly engage.
The outer coating of the cable has to be fully enclosed by the compression nipple.
Fix luminaire with enclosed or any other suitable fixing material onto the mounting surface. Place glass into luminaire housing, close luminaire with the cap and screw in knob into the cap.

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Loosen lateral knob, remove cap and take out glass.
Please follow the installation instructions for the LED module.
Defective glass must be replaced.
Insert glass into luminaire housing, close luminaire with the cap and screw in knob into the cap.