BEGA 51150.6 Indoor Table Lamp Instruction Manual

BEGA 51150.6 Indoor Table Lamp

Product Information

Safety| The installation and operation of this luminaire are subject tonational safety regulations. The manufacturer accepts no liabilityfor damage caused by improper use or installation. If subsequentmodifications are made to the luminaire, the person responsible forthese modifications shall be considered the manufacturer.
---|---
Overvoltage Protection| The electronic components installed in the luminaire areprotected against overvoltage in accordance with DIN EN 61547. Toachieve an additional protection against e.g. transients, etc. werecommend separate overvoltage protection components. You can findthem on our website at www.bega.com.
Leuchtmittel| Modul-Anschlussleistung: 8.5 W
Leuchten-Anschlussleistung| 10 W
Bemessungstemperatur| ta max = 25°C
Umgebungstemperatur| ta max = 50°C
Leuchtmittel Modul-Bezeichnung| LED-0581/930
Farbtemperatur| 3000 K
Farbwiedergabeindex| CRI > 90
Modul-Lichtstrom| 1200 lm
Leuchten-Lichtstrom| 664 lm
Leuchten-Lichtausbeute| 66.4 lm / W

Application

• Table lamp · indoor luminaire with wide beam light distribution.
• Luminaire for positioning on a wooden base for a variety of lighting situations with adjustable light.
• Wooden base optionally available in three different colour versions, as listed below.

Product Usage Instructions

1. LEDs are high-quality electronic components! Please avoidtouching the light output opening of the LED directly duringinstallation or relamping.
2. Set the desired beam direction by tilting the luminaire.
3. Replacing the LED module:
4. The designation of the LED module is noted on a label in theluminaire.
5. The light color and light output of BEGA replacement modulescorrespond to those of the modules originally fitted.
6. The module can be replaced by qualified persons using standardtools.
7. Disconnect the electrical installation.
8. Open the luminaire.
9. Please follow the installation instructions for the LEDmodule.
10. Close the luminaire.
11. For this luminaire, wooden bases in 3 surfaces are optionallyavailable. Wooden bases are accessories and must be orderedseparately.

Product description

1. Table lamp »STUDIO LINE«
2. Cast aluminium luminaire housing, finish Colour velvet black, inside hue matt copper
3. Trim ring · Chrome finish
4. Clear safety glass
5. Light-diffusing silicone lens
6. Reflector made of pure anodised aluminium
7. Cable dimmer (touch-controlled dimmer) for infinite light adjustment
8. Black cable · 2,5m, with safety plug
9. LED power supply unit 220-240 V y 50-60 Hz

Safety class I

1. CE – Conformity mark
2. Weight: 1.2 kg
3. This product contains light sources of energy efficiency class(es) E

Safety

1. The installation and operation of this luminaire are subject to national safety regulations.
2. The manufacturer accepts no liability for damage caused by improper use or installation.
3. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

1. The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
2. To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
3. You can find them on our website at www.bega.com.

Lamp

• Module connected wattage 8.5 W
• Luminaire connected wattage 10 W
• Rated temperature ta=25 °C
• Ambient temperature ta max=50 °C

51 150.6K3

• Module designation LED-0581/930
• Colour temperature 3000 K
• Colour rendering index CRI > 90
• Module luminous flux 1200 lm
• Luminaire luminous flux 664 lm
• Luminaire luminous efficiency 66,4 lm/W

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• For precise positioning of reflector and cover ring, it is advisable to lift the luminaire at the connecting cable. The opening of the luminaire housing points downwards.
• Screw enclosed trim ring with attached reflector into the luminaire housing by turning it clockwise.
• Position luminaire on the separate wooden base. Insert the connecting cable into the groove of the wooden base.
• For this purpose, wooden bases in three different surfaces are available – accessories 13 318, 13 319 and 13 320.
• Connect luminaire to mains supply (230 V).
• Press sensing device gently to turn the luminaire on or off.
• Holding the sensing device enables to adjust the light intensity infinitely.
• Set the desired beam direction by tilting the luminaire.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the electrical installation.
• Open the luminaire.
• Please follow the installation instructions for the
• LED module.
• Close the luminaire.

Accessory · Wooden bases

• For this luminaire wooden bases in 3 surfaces are optional available.
• Wooden bases are accessories and must be ordered separately.
• Part. No
• Natural oak 13 318
• Ash black 13 319
• Ash white 13 320

Spares

BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>