BEGA 22256 Wall Luminaire Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 22256 Wall Luminaire
Product Information
Product Usage Instructions
DIMENSIONS
Instructions for use
Product Description
Installation
Cleaning Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 22256 Wall Luminaire

BEGA-22256-Wall-Luminaire-product

Product Information

The Wandleuchte Wall luminaire Applique is a robust luminaire designed for glare-free lighting of walls, traffic areas, and house entrances. It offers excellent lighting qualities and is suitable for both indoor and outdoor use. The luminaire has an IP65 rating, ensuring its resistance to dust and water.

The luminaire comes with LED modules that provide efficient lighting. There are two module options available: LED-0281/830 with a color temperature of 3000 K and LED-0281/840 with a color temperature of 4000 K. Both modules have a color rendering index (CRI) greater than 80, ensuring accurate color representation.

The connected wattage for the modules is 17.6 W, while the connected wattage for the luminaire is 20 W. The module luminous flux for LED-0281/830 is 3340 lm, and for LED-0281/840 is 3435 lm. The luminaire luminous flux for LED-0281/830 is 1749 lm, and for LED-0281/840 is 1799 lm. The luminaire has a high luminous efficiency, with 87.5 lm/W for LED-0281/830 and 90 lm/W for LED-0281/840.

Product Usage Instructions

Ensure that the installation and operation of the luminaire comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning.
To protect the electronic components from overvoltage, it is recommended to use separate overvoltage protection components.
Avoid touching the light output opening of the LED directly during installation or relamping to prevent damage to the high-quality electronic components.
Place the enclosed desiccant pouch in the luminaire to maximize the service life of the electrical components. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label before closing the luminaire.
Make sure to make an earth conductor connection between the luminaire top and base. Ensure that the gasket is positioned correctly.
Replace the luminaire top and tighten the screws evenly. Tighten the screws uniformly in a crosswise fashion.

Wall luminaire

DIMENSIONS

$BEGA-22256-Wall-Luminaire-fig- $1$$

Instructions for use

Application
Wall luminaire for glare-free lighting of walls, traffic areas and house entrances. Very robust luminaire with excellent lighting qualities.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure® coating technology Matt safety glass Silicone gasket Reflector made of pure anodised aluminium 2 mounting holes ø 5 mm Distance apart 100 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ 2-pole connecting terminal for digital control Connecting terminal and earth conductor terminal 2.5@ BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables BEGA Thermal Control® Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK09
Protection against mechanical
impacts < 10 joule
Safety mark
Conformity mark
Weight: 1.8 kg

This product contains light sources of energy efficiency class(es) C

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.

You can find them on our website at www.bega.com

Lamp

Module connected wattage: 17.6 W
Luminaire connected wattage: 20 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 45 °C
22 256 K3
Module designation: LED-0281/830
Color temperature: 3000 K
Color rendering index: CRI > 80
Module luminous flux: 3340 lm
Luminaire luminous flux: 1749 lm
Luminaire luminous efficiency: 87,5 lm / W
22 256 K4
Module designation: LED-0281/840
Color temperature: 4000 K
Color rendering index: CRI > 80
Module luminous flux: 3435 lm
Luminaire luminous flux : 1799 lm
Luminaire luminous efficiency : 90 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the screws and lift off the luminaire top. Lead the main supply cable through the cable entry into the luminaire housing.
Note : the position of application of the luminaire
“arrow down”.
Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Make an earth conductor connection between the luminaire top and the luminaire base.
Make sure that gasket is positioned correctly. Replace the luminaire top and tighten the screws evenly.
Tighten the screws uniformly in a crosswise fashion.

Cleaning Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares