BEGA 50114 Ceiling and Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50114 Ceiling and Wall Luminaire Instruction Manual
Dimension
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass,
satin matt and metal housing, for all lighting tasks.
They are ideal for places where a soft and uniform lighting distribution is
required. Luminaire with a high protection class
Product description
Metal housing, finish Colour white
Hand-blown opal glass, satin matt,
with sliding-bolt closure
2 mounting holes ø 5.5mm
Distance apart 240mm
2 cable entries for through-wiring for mains
cable up to ø 10.5 mm max. 3 × 1.5@
Connection terminal 2.5@
Earth conductor connection
Lampholder E 27
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
Impact strength IK03
Protection against mechanical
impacts < 0.35 joule
– Safety mark
– Conformity mark
Weight: 2.7 kg
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
Lead mains supply cable through the cable entry into the luminaire housing.
Notice position of application »arrow down« when installed at the wall.
Fix the luminaire housing with enclosed or any other suitable fixing material
onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
Insert lamps.
Place glass to the luminaire housing and observe that the holding springbolts
fit into the notches of the glass.
Turn the glass clockwise until it is locked.
Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the luminaire housing, turn it counter-clockwise.
Lamp
Luminaire with screw base E 27
Lamp output max. 75 W
This product contains light sources of energy efficiency class E
Supplied lamp
BEGA LED lamp 13548
LED Retrofit 7 W · 805 lm · 2700 K dimmable
Supplied lamp
BEGA LED lamp 13586
LED Retrofit 7 W · 805 lm · 3000 K dimmable
Luminaire efficiency: 61.6%
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be
inserted into the trim ring (accessory)
Relamping · Maintenance
Disconnect the electrical installation.
Take off glass from luminaire housing.
Clean luminaire and glass. Use only solvent-free cleansers.
Change the lamp.
Insert glass into luminaire housing
Accessory · Trim rings
For this luminaire metal trim rings in 3 surfaces are optional available.
Trim rings are accessories and must be ordered separately
tem Part. No
Colour White 13 079
Stainless steel 13 080
Chrome 13 081
Spares
Spare glass 11 003 177 .0RG
LED lamp 2700 K 13 548
LED lamp 3000 K 13 586
Lampholder 63 000 355
Reflector 76 000 678
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>