BEGA 50742.4 Indoor Floor Lamp Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 50742.4 Indoor Floor Lamp
Product Usage Instructions
Instructions for use
Product Description
Safety
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50742.4 Indoor Floor Lamp

Product Information

Safety: The installation and operation of this luminaire are subject to national safety regulations. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients,etc., we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
Lamp Module connected wattage: 35 W
Luminaire connected wattage: 39.5 W
Rated temperature: 25°C
Ambient temperature: 50°C
Module designation: 2x LED-1226/930
Colour temperature: 3000 K
Colour rendering index (CRI): > 90
Module luminous flux: 5630 lm
Luminaire luminous flux: 2220 lm
Luminaire luminous efficiency: 56.2 lm / W

Product Usage Instructions

Carefully remove the floor lamp from its packaging and set it up. Ensure that the luminaire is in a firm and secure position.
Guide the luminaire shield provided over the synthetic cover of the luminaire and adjust it to its end position.
Connect the luminaire to the mains supply (230 V).
Press the foot dimmer gently to turn the luminaire on or off. Holding the sensing device enables you to adjust the light intensity infinitely.
To replace the LED module, note the designation of the LED module on a label in the luminaire.
Disconnect the system and open the luminaire.
Follow the installation instructions for the LED module. Qualified persons can replace the module using standard tools.
If the luminaire cover is defective, it must be replaced. Close the luminaire after replacing the cover.

Floor lamp for indoor use

Instructions for use

Application
Floor lamp · indoor luminaire with impact-resistant synthetic diffuser and metal housing for shielded light, deflected upwards and downwards.

Product Description

Floor lamp »STUDIO LINE«
Metal housing, finish Colour velvet black Aluminium housing shield,
Finish Colour velvet black inside hue matt brass
Impact-resistant synthetic cover, translucent white
Foot dimmer for infinite light adjustment
Black cable · 2 m, with safety plug
LED power supply unit 220-240 V y 50-60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
– Conformity mark
Weight: 10.5 kg

This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage 35 W
Luminaire connected wattage 39.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 50 °C

50 742.4 K3

Module designation 2x LED-1226/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 5630 lm
Luminaire luminous flux * 2220 lm
Luminaire luminous efficiency * 56,2 lm / W
preliminary data

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Carefully remove the floor lamp from its packaging and set it up. Make sure that the luminaire is in a firm and secure position. Guide the luminaire shield provided over the synthetic cover of the luminaire and adjust it in its end position.
Connect luminaire to mains supply (230 V). Press foot dimmer gently to turn the luminaire on or off.
Holding the sensing device enables to adjust the light intensity infinitely.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.
We recommend that you dry-clean the foot dimmer.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Defective luminaire cover must be replaced. Close the luminaire.

Spares