BEGA 51191.6 Illuminated Mirror for Indoor Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 51191.6 Illuminated Mirror for Indoor
Product Information
Product Usage Instructions
Instructions for use
Product description
Overvoltage protection
Installation
Cleaning · Maintenance
Replacing the LED module
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 51191.6 Illuminated Mirror for Indoor

Product Information

The product is a luminaire with electronic components that are protected against overvoltage in accordance with DIN EN 61547. It is recommended to use separate overvoltage protection components for additional protection. The luminaire is subject to national safety regulations and should only be installed and operated by a qualified electrician. The manufacturer does not accept liability for damage caused by improper use or installation. The luminaire has a lamp module connected wattage of 27W and a luminaire connected wattage of 30W. The rated temperature is between 25°C and 50°C. The module designation is LED-1301/930 and it has a colour temperature of 3000K. The colour rendering index (CRI) is greater than 90. The module luminous flux is 4200lm and the luminaire luminous flux is 522lm. The luminaire has a luminous efficiency of 17.4lm/W.

Product Usage Instructions

During installation or relamping, avoid touching the light output opening of the LED directly.
Remove the luminaire housing (reflector) from the packaging.
Pass the power connecting cable through the cable entry into the luminaire housing.
Secure the luminaire housing to the installation surface using the provided fixing materials or other suitable materials.
If replacing the LED module, disconnect the system and open the luminaire.
Follow the installation instructions for the LED module.
Replace any defective luminaire cover.
Close the luminaire.

For spare parts, the following are available:

LED power supply unit: DEV-0305/700i
LED module 3000K: LED-1301/930
Mirror: 75 005 089
Reflector: 75 005 257

Instructions for use

Application
Illuminated mirror · Indoor luminaire with velvet white metal housing.
Luminaire with light source shielded to the front and metallic inside colour of the reflection surface.
Radial light emission 360°.

Product description

Luminaire housing made of aluminium, surface Colour velvet white inside hue matt copper
Inside synthetic cover, translucent white Mirror made of crystal glass, diameter 400 mm, visible edge polished
4 mounting holes ø 6 mm
Distance 260 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@ Connection terminal 2.5@
Earth conductor connection
2-pole connecting terminal for
digital control
LED power supply unit
220-240 V x 0/50-60 Hz
DC 196-250 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
– Conformity mark
Weight: 6.1 kg
This product contains light sources of energy efficiency class(es) D

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage: 27 W
Luminaire connected wattage: 30 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 50 °C

51 191.6 K3

Module designation: LED-1301/930
Colour temperature: 3000 K
Colour rendering index: CRI > 90
Module luminous flux: 4200 lm
Luminaire luminous flux: 522 lm
Luminaire luminous efficiency: 17,4 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Remove the luminaire housing (reflector) from the packaging. Pass the power connecting cable through the cable entry into the luminaire housing. Secure the luminaire housing to the installation surface with the fixing materials provided or other suitable materials.

Note position of application of the luminaire housing “arrow down”. Connect the earth conductor to the earthing screw ( ) of the luminaire housing. Remove the mounting plate with LED unit from its packaging. Loosen 4 Torx screws (T 20) and remove the central service panel from the LED unit. Loosen earth connection (plug connection) between central service panel and LED unit. Guide wires of the power connecting cable through the rear opening into the LED unit. Place the LED unit over the keyholes onto the four threaded bolts of the luminaire housings and turn it clockwise until it stops.

Tighten the hex nuts M5 over the keyholes. Make the electrical connection to the terminals. Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N). The two connecting terminals marked DA, DA are provided for digital control purposes. If these terminals are not assigned, the luminaire will work with full light output. Establish the earth conductor connection of the LED unit to the luminaire housing (plug connector). Make earth connection (plug connection) from the central service panel to the LED unit again. Place the central service panel back onto the LED unit and fasten using the 4 Torx screws (T20). Remove the mirror from its packaging. Place the rear locking bolts of the mirror fastening onto the 3 elongated recesses of the LED unit. Turn the mirror clockwise against the resistance until the locking bolts audibly click into their final position.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Defective luminaire cover must be replaced. Close the luminaire.