BEGA 50018 LED Ceiling and Wall Luminaire Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

Application
Dimension
Product description
Safety
Overvoltage protection
Lamp
50 018K27
50 018K3
Installation
Accessory · Trim rings
Spares
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50018 LED Ceiling and Wall Luminaire

Application

Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.

Dimension

Product description

Metal housing, finish Colour white Hand-blown opal glass, satin matt, with bayonet closure 2 mounting holes ø 6mm Distance apart 340mm 2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@

Connection terminal 2.5

@ Earth conductor connection

LED power supply unit

220-240 V 0/50-60 Hz DALI-controllable

Number of DALI addresses: 1

Basic insulation is provided between the mains and control cables BEGA Thermal Control®

Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire Safety class I

Impact strength IK06 Protection against mechanical impacts < 1 joule

– Safety mark
– Conformity mark

Weight: 4.2 kg

This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.

Installation and commissioning may only be carried out by a qualified electrician.

The manufacturer accepts no liability for damage caused by improper use or installation.

If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.

To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.

You can find them on our website at www.bega.com.

Lamp

Module connected wattage 42.6 W
Luminaire connected wattage 47.4 W
Rated temperature ta=25 °C
Ambient temperature ta max=40 °C

50 018K27

Colour temperature 2700 K
Colour rendering index CRI >90
Module luminous flux 6225 lm
Luminaire lumino

us flux 3581 lm
Luminaire luminous efficiency 75,5 lm/W

50 018K3

Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 6435 lm
Luminaire luminous flux 3703 lm
Luminaire luminous efficiency 78,1 lm/W

Luminaire with trim ring:

Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Pass the mains supply cable through the grommet into luminaire housing. Fix luminaire housing with enclosed or any other suitable fixing material on to the mounting surface.

It is imperative to use the enclosed gaskets.

Dismantle the mains supply cable approx. 60 mm.

Make earth and electrical connection to the terminals.

For digital control please use the connecting terminal DA, DA.

In case this terminal is not used the luminaire will be operated at full light output.

Place glass to the luminaire housing and observe that the cam pins fit into the notches of the glass.

Screw in glass by turning it clockwise. Thus, you reach a safe and vibration- resistant holding of the glass.

To release the glass from the luminaire housing turn it counter-clockwise.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire.

The light colour and light output of BEGA replacement units correspond to those of the

LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.