BEGA 50 081 Ceiling and Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Instructions for use
Product description
Installation
Accessory · Trim rings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50 081 Ceiling and Wall Luminaire for Indoor Use Instruction Manual

Instructions for use

Dimensions

Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.

Product description

Metal housing, finish Colour white
Hand-blown opal glass, satin matt, with sliding-bolt closure 3 fixing holes ø 5.5mm 2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@
Connecting terminal 2.5@ with plug connection
Earth conductor connection 2-pole connecting terminal fordigital control
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water
Impact strength IK03
Protection against mechanical impacts < 0.35 joule
Safety mark
Conformity mark
Weight: 5.8 kg

This product contains light sources of energy efficiency class(es) D

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp
Module connected wattage 60 W
Luminaire connected wattage 64.5 W
Rated temperature ta=25 °C
Ambient temperature ta max=30 °C

50 081K3
Module designation LED-0630/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 7105 lm
Luminaire luminous flux 4767 lm
Luminaire luminous efficiency 73,9 lm/W

Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Disassemble LED module. Loosen LED-connection and earth connection (plug connection). Dismantle the mains supply cable max. 80 mm. Lead mains supply cable through the cable entry into the luminaire housing. Fix the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface. It is imperative to use the enclosed gaskets. Make earth and electrical connection to the terminal. For digital control please use the connecting terminal DA, DA. In case this terminal is not used the luminaire will be operated at full light output. Make earth connection between LED module and luminaire housing (plug connection). Push LED-plugs into couplers as far as it will go. Assemble LED module. Tighten the screws evenly. Please observe that the LED board is not damaged mechanically. Place glass to the luminaire housing and observe that the holding springbolts fit into the notches of the glass. Turn the glass clockwise until it is locked. Thus, you reach a safe and vibration-resistant holding of the glass. To release the glass from the luminaire housing, turn it counter-clockwise.

Replacement of the LED module · Maintenance

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Please follow the installation instructions for the
LED module.
Screw in glass by turning it clockwise as far as it will go.
A broken glass must be replaced.