BEGA 51 222.6 Illuminated Mirror for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
51 222.6 Illuminated Mirror for Indoor Use
Instruction Manual
51 222.6
Illuminated mirror for indoor use
51 222.6 Illuminated Mirror for Indoor Use
Instructions for use
Application
Illuminated mirror · Indoor luminaire with velvet black metal housing.
Luminaire with light source shielded to the front and metallic inside colour
of the reflection surface.
Radial light emission 360°.
Product description
Luminaire housing made of aluminium, surface Colour velvet black inside hue
matt copper
Inside synthetic cover, translucent white Mirror made of crystal glass,
diameter 550 mm, visible edge polished 4 mounting holes ø 6 mm Distance 350 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x
1.5@ Connection terminal 2.5@
Earth conductor connection 2-pole connecting terminal for digital control
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-280 V
During DC operation the LED power is reduced to 15 %
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
– Conformity mark
Weight: 10.3 kg
This product contains light sources of energy efficiency class(es) D
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Lamp
| Module connected wattage | 53.1 W |
|---|---|
| Luminaire connected wattage | 59 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 45 °C |
51 222.6 K3
| Module designation | LED-1302/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 7900 lm |
| Luminaire luminous flux | 901 lm |
| Luminaire luminous efficiency | 15,3 lm / W |
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Remove the luminaire housing (reflector) from the packaging.
Pass the power connecting cable through the cable entry into the luminaire
housing.
Secure the luminaire housing to the installation surface with the fixing
materials provided or other suitable materials.
Note position of application of the luminaire housing “arrow down”.
Connect the earth conductor to the earthing screw (1) of the luminaire
housing.
Remove the mounting plate with LED unit from its packaging.
Loosen 4 Torx screws (T 20) and remove the central service panel from the LED
unit.
Loosen earth connection (plug connection) between central service panel and
LED unit.
Guide wires of the power connecting cable through the rear opening into the
LED unit.
Place the LED unit over the keyholes onto the four threaded bolts of the
luminaire housings and turn it clockwise until it stops.
Tighten the hex nuts M5 over the keyholes.
Make the electrical connection to the terminals.
Observe the correct configuration of the connecting cable. Connect the live
conductor to the brown wire (L) and the neutral conductor to the blue wire
(N).
The two connecting terminals marked DA, DA are provided for digital control
purposes.
If these terminals are not assigned, the luminaire will work with full light
output.
Establish the earth conductor connection of the LED unit to the luminaire
housing (plug connector).
Make earth connection (plug connection) from the central service panel to the
LED unit again. Place the central service panel back onto the LED unit and
fasten using the 4 Torx screws (T20).
Remove the mirror from its packaging.
Place the rear locking bolts of the mirror fastening onto the 3 elongated
recesses of the LED unit.
Turn the mirror clockwise against the resistance until the locking bolts
audibly click into their final position.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Defective luminaire cover must be replaced.
Close the luminaire.
Spares
| LED power supply unit | DEV-0315/1050i |
|---|---|
| LED module 3000 K | LED-1302/930 |
| Mirror | 75 005 090 |
| Reflector | 75 005 261 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60 · 58689 Menden
· info@bega.com
· www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>